Login

kennyw · 03-15-2017, 01:01 PM

I was going to design and build my own brackets and use ammo cans but these came up for a good price and I couldn't pass them up. However, they are not designed to work with the Honda rack. But I am not easily deterred either.

After a little fiddling I was able to mount the brackets by replacing the rear spacers in the Honda rack hardware.

[Image: a6f15ddce359a22d70a28fda1edda948.jpg]

[Image: a6f15ddce359a22d70a28fda1edda948.jpg]

[Image: cc8475b8c5b213f896474bf15bb499ee.jpg]

[Image: 11b5c4e161e9af7e1cfbdb9f504c5bfa.jpg]

[Image: 1c62a8693bba94c6830c11e676e7cb40.jpg]

[Image: dfc163b94f8fa66f1b9c32d6ec50d9ff.jpg]

[Image: 12c30de5d5498ee6efd8c9feb3dfd263.jpg]

[Image: 38ae52d4221e13d6ce881715f8631465.jpg]

[Image: 4952af240ac0b72bf1b0bc0685da851a.jpg]

[Image: fdf729c3d2368178e45e6a312640c1e0.jpg]

This is the spacer that made everything fit. 3/4" long.
[Image: 36fc01b581b43241d53acc1bf08b4a0d.jpg]

Lord Popgun · 03-15-2017, 09:14 PM

Nice job Kenny! They look great!

If that spacer is all it takes, you would think the manufacturer could have figured that out and included them.

kennyw · 03-15-2017, 09:50 PM

They are mounted a little tighter to the bike like this and could rub on the rack a little. Nothing bad, but enough that it could make a mark over time on the inside, non visible side.

The rack fitment is also not ideal but it goes together if all 4 bolts are installed loose before tightening anything. The rack then conforms to the spacers when tightened and has plenty of flex to accommodate the needed spacers. I don't expect any issues with it.

Lord Popgun · 03-15-2017, 10:15 PM

Any plans for the turn signals?

kennyw · 03-15-2017, 10:35 PM

(03-15-2017, 10:15 PM)Lord Popgun_imp Wrote: Any plans for the turn signals?

I already had them relocated to the license plate.

PowerDubs_imp · 03-15-2017, 11:25 PM

Good job.

I've also purchased a set of these cases and they should arrive today. I am nervous to see if they will fit with my sissybar and/or my Kimija bar.

Any reason you left the factory grab handle blinker mount pieces on the bike? They aren't doing anything other than wasting weight. I left mine off even with the Kimija grab bar- cleans up the classic look.

kennyw · 03-15-2017, 11:28 PM

If I take them off, I would need to get longer spacers. The rack is wide and intended to go on top of the grab rail with the supplied spacers/hardware.

PowerDubs_imp · 03-15-2017, 11:47 PM

Technically so is the Kimija- it flexes just fine.

[Image: 40a6e50fef659196af2c011001591751.jpg]

[Image: 68f0acb64d188e04b248234f5fe94e25.jpg]

emptysea · 03-16-2017, 12:50 AM

Looks great, Kenny. A little bummed that you didn't do the ammo cans because then you could have been the guinea pig for what I want to do with my bike. LOL

Great job.

4 Paws_imp · 03-19-2017, 05:06 AM

Looks so much better than ammo cans!

Ammo cans on a KLR or Ural at fine but not on a CB!

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	Delkevic 9" Oval Install Problems.	jbird06_imp	4	377	06-11-2024, 08:25 AM Last Post: devildogdoc_imp
	Install a 6-speed trans on a 2013?	amacbeth_imp	37	2,621	02-21-2023, 12:22 PM Last Post: PowerDubs_imp
	17 tooth CS sprocket install, comments.	Bike #12_imp	11	729	01-03-2022, 08:30 AM Last Post: misterprofessionality
	Tail light install problem	iamheero_imp	9	558	11-27-2021, 02:58 AM Last Post: Bazbro_imp
	Engine Guard Install Question?	linuxology_imp	27	1,339	07-25-2020, 08:52 PM Last Post: Houtman_imp
	Would love some input on the install of the factory heated grips.	Tim_imp	2	243	05-06-2018, 03:08 AM Last Post: Tim_imp
	Grip install. Again. Grr.	Inhouse Bob	9	493	03-29-2018, 07:10 AM Last Post: the Ferret
	Road Comet 2 Install	letsjet_imp	20	928	02-12-2017, 05:51 AM Last Post: ClassicVW_imp
	Diy Bar end mirrors install	Matt F._imp	5	326	04-18-2016, 11:24 PM Last Post: Motogeezer1949_imp
	Gear Indicator Install	1100rider_imp	108	5,193	11-29-2015, 10:28 PM Last Post: Lord Popgun