Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Smooth Power Everywhere II
#17
Installed my PCV last night. Two hardest parts were removing the fuel line from the tank and routing the PCV wire harness through the frame. Finally figured out how to just squeak the plugs by the frame tube down low on the left side and then run up by the tank. Everything fits very nice and neat the the PCV is a solid and well built piece in my opinion. Plugs and wiring are first rate. PCV fits very nicely into the cubby holder behind the tank. Still have room for my tools and rags.

Bikes fired right up and ran smoothly. I rode the bike to work today and put about 50 miles on in mixed heavy traffic and highway speed use. Bike idles at just a bit over 1,000 RPM warm (say 1050). Just off idle in slow stop and go is very smooth. Bike has very smooth throttle in all gears and pulls like a freight train from say 50 - 90mph+. I nailed it at coming home for lunch today and the bike is very fast. I am running an Arrow slip on muffler and a K&N filter. No other mods. There is a slight bit of popping on decal but attribute that to the air injection. Have not decided to close that off yet.

I think with the slip on and filter, the PCV has met my expectations. Would I put it on a stock bike? Not sure. My bike ran so well in stock form. I had nothing to complaint about.
Reply


Messages In This Thread
Smooth Power Everywhere II - by CB4ME_imp - 04-05-2014, 07:42 AM
RE: Smooth Power Everywhere II - by Dakota_imp - 04-05-2014, 09:42 AM
RE: Smooth Power Everywhere II - by CB4ME_imp - 04-05-2014, 12:39 PM
RE: Smooth Power Everywhere II - by CB4ME_imp - 04-05-2014, 11:48 PM
RE: Smooth Power Everywhere II - by gary_imp - 04-06-2014, 02:08 AM
RE: Smooth Power Everywhere II - by CB4ME_imp - 04-06-2014, 07:28 AM
Smooth Power Everywhere II - by Elipten_imp - 04-06-2014, 10:31 AM
RE: Smooth Power Everywhere II - by CB4ME_imp - 04-09-2014, 03:59 AM
RE: Smooth Power Everywhere II - by the Ferret - 04-09-2014, 08:18 AM
RE: Smooth Power Everywhere II - by SUPERCRUZ_imp - 04-10-2014, 09:19 AM
RE: Smooth Power Everywhere II - by Dave_imp - 04-10-2014, 10:42 AM
RE: Smooth Power Everywhere II - by CB4ME_imp - 04-10-2014, 09:56 PM
RE: Smooth Power Everywhere II - by Tortuga_imp - 04-18-2014, 10:31 AM
RE: Smooth Power Everywhere II - by Dave_imp - 04-19-2014, 02:55 AM
RE: Smooth Power Everywhere II - by CB4ME_imp - 04-19-2014, 06:38 AM
RE: Smooth Power Everywhere II - by Greg_imp - 04-30-2014, 11:59 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  GPS power cable The Gecko_imp 10 1,043 10-06-2023, 12:40 AM
Last Post: suhawk305
  Has anyone installed a power commander in? Doug Shepard_imp 3 507 08-10-2023, 07:20 AM
Last Post: Doug Shepard_imp
  Power source for oil indicator led norton1974_imp 1 283 12-31-2022, 10:07 AM
Last Post: Cormanus
  Power Commander V question HBFL_imp 1 264 08-23-2022, 05:41 PM
Last Post: jtopiso_imp
  Power Commander Tune Maps. mvk24_imp 43 3,130 01-03-2022, 08:16 AM
Last Post: SoCal CB1100_imp
  2010 model Power Commander alternative? 83NZA_imp 7 637 08-03-2021, 02:04 PM
Last Post: Aussieflyer
  Smooth shifting DougsZ28_imp 16 1,405 07-09-2021, 07:32 AM
Last Post: GoldOxide_imp
  Transmission power routing and speeds LakeWylieJoe_imp 6 646 01-10-2021, 10:30 AM
Last Post: jimgl3_imp
  Guhl Reflash vs. power commander with custom map. misterprofessionality 9 775 09-06-2020, 03:59 AM
Last Post: PowerDubs_imp
  Cheap airflow / power gains PowerDubs_imp 7 626 07-21-2020, 01:59 AM
Last Post: Cobalt23_imp

Forum Jump:


Users browsing this thread: 1 Guest(s)