Side Stand Foot

[redbirds_imp]

I like this and could have used it a few times.

Webike: Motorcycle Parts, Accessories, Gears, OEM parts & Reviews

 

[Lord Popgun]

Oooooh, and in 3 colors too. Kinda pricey, but I like it.

 

[Chapomis_imp]

I'll take a black one

 

[pdedse]

Not saying they ain't nice lookin'

...cause they are...

But at $53 and change?

I think I'll stick with mine...

I'm only out the 5 cents I don't collect on my deposit!

Sorry...:blush: I'm still recovering from paying cash for the new '14 standard!

 

[Chapomis_imp]

:rofl: take that Redbirds (I still think they are pretty cool though)

 

[redbirds_imp]

Heck, we don't even get a deposit in Georgia. Lol

 

[pdedse]

Not saying they ain't nice lookin'

...cause they are...

But at $53 and change?

I think I'll stick with mine...

I'm only out the 5 cents I don't collect on my deposit!

Sorry...:blush: I'm still recovering from paying cash for the new '14 standard!

Keep in mind my other bike is a KLR650 so hence...the can.

 

[NightRider_imp]

Not saying they ain't nice lookin'

...cause they are...

But at $53 and change?

I think I'll stick with mine...

I'm only out the 5 cents I don't collect on my deposit!

Sorry...:blush: I'm still recovering from paying cash for the new '14 standard!

I am rolling on the floor with this one! Thanks!

 

[4 Paws_imp]

I use a piece of punched aluminum scrap, drilled a hole in it and threaded some cord through to loop over the handlebars. When I need to use it I just toss it on the ground, position with cord and my foot and drop side stand. On leaving I crank up, pull up the cord and ride away.
Almost pulled the trigger on a fancy one but decided it's cost was equal to at least a thousand miles of gasoline.

 

[the Ferret]

"Almost pulled the trigger on a fancy one but decided it's cost was equal to at least a thousand miles of gasoline."

about 1500 miles for me at 1.78 a gallon and 54 miles to the gallon..or roughly all the gas I will use going to the rally and back in May.

 

[kmoney_imp]

Reminds me of the Revzilla stand pad review.

 

[Chapomis_imp]

Pretty Funny

 

[CB4ME_imp]

A footpad that's always on the bike has its attractions, but beware the hazards of overly large side stand feet. Besides reducing parked lean angle, wider feet proscribe a larger arc and can hit the pavement before the side stand is set. They can also give you a false sense of security. I know this because I dropped one of my bikes twice. The foot was flat with the ground but the side stand hadn't gone past vertical. The slight downward pitch of the ground was all it took for the bike to roll forward and hit the dirt 20 seconds after I walked away. My NC700X no longer wears a foot pad.

The CB1100 has a relatively small side stand foot, and it's sunk in the dirt or grass on many occasions. I decided to make my own low profile pad and have so far escaped any negative consequences.

 

[redbirds_imp]

I like that CB, what materials did you use?

 

[CB4ME_imp]

I used 1/8" aluminum. Bottom flat plate, middle plate the fits the contour of the side stand foot, and a top plate that overlaps the foot. Flat head machine bolts secure the 3 plates.

It won't hold up the bike in wet sand but doubles the OEM footprint.

 

[redbirds_imp]

I used 1/8" aluminum. Bottom flat plate, middle plate the fits the contour of the side stand foot, and a top plate that overlaps the foot. Flat head machine bolts secure the 3 plates.

It won't hold up the bike in wet sand but doubles the OEM footprint.

Thanks, I now have a project.

 

[Chapomis_imp]

I used 1/8" aluminum. Bottom flat plate, middle plate the fits the contour of the side stand foot, and a top plate that overlaps the foot. Flat head machine bolts secure the 3 plates.

It won't hold up the bike in wet sand but doubles the OEM footprint.

Thanks, I now have a project.

Thanks, I now have a project.
I was thinking the same thing Steve, except that I was thinking about using rivets instead of bolts. It might mean removing the side stand, but it would be a clean look.

 

[Cormanus]

I've got a simpler, more enjoyable project.

 

[Lord Popgun]

So what's the good beer in OZ. American advertising would lead you to believe it's Fosters. I've heard that's not it...

 

[Cormanus]

You've heard right, popgun! :beerchug:

It's now a hard question to answer. Once upon a time, unless you were a traitor, it was the draft beer produced by your local brewery. An exotic beer was one from another state. The big corporates started buying breweries and the beer became homogenous until the whole craft beer thing caught on. Now you can find any number of good craft beers depending on your taste. Of the 'big' brewery stuff, Coopers from South Australia make a good drop.

As for Fosters, there was a time when it was common; nowadays I seldom see it. I suspect most of it goes to Europe, the UK and the US and you are all very welcome to it. Similarly, you can hang on to Budweiser.

If I sound like I know what I'm talking about, I don't. Once when I was away riding with Pterodactyl, I ordered a craft(ish) beer in a pub. He asked me whether I could tell the difference between it and the mass-produced concoction he was drinking. Of course, I said, so he put me to the test. I failed.