Posts: 8
Threads: 2
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: May 2019
I have a 2013 CB1100. It hasn't been started for 3 months and when I started it today, I discovered a problem with shifting gears. When I shifted into 1st gear the bike started to creep ahead. I let out the clutch and the bike moved ahead. However, I could not shift it into 2nd gear. I road around in 1st gear for awhile and then stopped. I could not get it to shift into neutral. I shut the bike off and was then able to get it into neutral. I then started the bike again and shifted into 1st and it started to creep forward again. I let out the clutch and moved ahead. Again I could not shift into 2nd gear. After several tries I finally got it into 2nd gear. I rode around in 2nd but could not get it into 3rd.
My first thought is that the clutch master cylinder is not working and therefore the clutch is not releasing. It seems that the clutch lever does not have much resistance when I pull on it. Is it possible that the seals in the master cylinder are leaking? Is there a way to check this out?
I assume there is a slave cylinder down at the clutch. Is that correct? If so, I assume there could be a problem with it not releasing the clutch.
Any thoughts or ideas would be greatly appreciated.
Posts: 8,026
Threads: 21
Likes Received: 180 in 103 posts
Likes Given: 123
Joined: Apr 2025
More advanced mechanics will chime in, but the first thing I’d do is flush and bleed the fluid. And yes, there is a slave cylinder down there.
Posts: 50
Threads: 3
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Sep 2020
Sounds like the clutch packs are sticking or dragging. Might be worth an oil change as well as looking at clutch fluid.
Sent from my iPhone using Tapatalk
Posts: 1,670
Threads: 41
Likes Received: 137 in 65 posts
Likes Given: 34
Joined: Apr 2014
The above info is all good advice. Any clutch master cylinder leakage would be inside the master cylinder and not visible - but that's a rare failure. Oil change is a good idea also. If the oil is thick from an kind of additive, the plates might be dragging. Master cylinder flush and bleed is the second thing to check.
Posts: 8
Threads: 2
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: May 2019
Thanks guys for the input. I changed the oil less than 100 miles ago so I am going to address the clutch fluid first. I will flush and bleed the master/slave cylinders and report back on the results.
Posts: 23,403
Threads: 697
Likes Received: 482 in 220 posts
Likes Given: 597
Joined: Apr 2025
What oil did you use just out of curiosity?
Posts: 120
Threads: 3
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2014
At 15K miles, 5 years ,I had the brake & clutch fluid replaced on my 2013. The shop said the break fluid looked good but the clutch fluid looked nasty and really needed to be replaced. They emphasized nasty. Never had a problem though.
Posts: 12,677
Threads: 77
Likes Received: 3 in 3 posts
Likes Given: 0
Joined: Dec 2014
Is there a remote chance of master cylinder premature corrosion due to water in the system?
Posts: 23,403
Threads: 697
Likes Received: 482 in 220 posts
Likes Given: 597
Joined: Apr 2025
Well he said he changed the oil less than 100 miles before, and made no reference to the issue happening before the oil change which is why I asked.
If something changes after you have recently done something, always check that first.
Posts: 1,670
Threads: 41
Likes Received: 137 in 65 posts
Likes Given: 34
Joined: Apr 2014
(02-20-2021, 12:05 PM)gmike_imp Wrote: At 15K miles, 5 years ,I had the brake & clutch fluid replaced on my 2013. The shop said the break fluid looked good but the clutch fluid looked nasty and really needed to be replaced. They emphasized nasty. Never had a problem though.
Nobody knows why, but clutch fluid always turns dark faster, usually in a few thousand miles. Doesn't harm it though.
