removing both wheels

[GoldOxide_imp]

^^^ what he said.

I usually second guess myself on which spacer goes on which side of the axle for the front wheel. So I look up the parts diagram on line to verify.

2014 CB1100, 1981 KZ440 LTD, 1993 Yamaha XJ600 Seca, 1994 Yamaha XJ600 Seca

does paying attention to how they come off help?

does paying attention to how they come off help? Always, I usually put everything i take off in a place on the floor that mimics how it goes back together.

But I've made the mistake of kicking or moving the things accidentally. If that is the case you can always reference a schematic/parts diagram to verify.

2014 CB1100, 1981 KZ440 LTD, 1993 Yamaha XJ600 Seca, 1994 Yamaha XJ600 Seca

Understood. My stuff lies about outside on the ground because there is no garage. So keeping parts organized is important, but mishaps do happen.

[max]

Tom just be aware that when the bike is lowered too much in the front the center stand can collapse because of the angle from the base to the pivot point, so be careful to maintain the same height for the front forks.
Maybe loosen all fasteners for both wheels but leave them in place to minimize the force required to undo the various bolts and then remove them per wheel.

I have some ratchet loading straps that i use from the ceiling to the handle bars to stabilize and hold the front wheel off the ground, very reliably, many ways to do this

[Tom_imp]

I took both my wheels off to send them away to BartFactory to be made tubeless. I had some engine bars and car axle stands which made it very stable. See https://youtu.be/Yxr8lYkOOTA

Excellent video. Many thanks.

Tom just be aware that when the bike is lowered too much in the front the center stand can collapse because of the angle from the base to the pivot point, so be careful to maintain the same height for the front forks.
Maybe loosen all fasteners for both wheels but leave them in place to minimize the force required to undo the various bolts and then remove them per wheel.

I have some ratchet loading straps that i use from the ceiling to the handle bars to stabilize and hold the front wheel off the ground, very reliably, many ways to do this

Ratchet straps to the ceiling. I like that idea.

[LongRanger_imp]

^^^ what he said.

I usually second guess myself on which spacer goes on which side of the axle for the front wheel. So I look up the parts diagram on line to verify.

2014 CB1100, 1981 KZ440 LTD, 1993 Yamaha XJ600 Seca, 1994 Yamaha XJ600 Seca

does paying attention to how they come off help?

does paying attention to how they come off help? Always, I usually put everything i take off in a place on the floor that mimics how it goes back together.

But I've made the mistake of kicking or moving the things accidentally. If that is the case you can always reference a schematic/parts diagram to verify.

2014 CB1100, 1981 KZ440 LTD, 1993 Yamaha XJ600 Seca, 1994 Yamaha XJ600 Seca

Understood. My stuff lies about outside on the ground because there is no garage. So keeping parts organized is important, but mishaps do happen.

Understood. My stuff lies about outside on the ground because there is no garage. So keeping parts organized is important, but mishaps do happen.
Egg cartons, muffin tins, etc., will keep things organized and in order of disassembly.

[Django]

These are mine:





Well, that was a little bit more than tire change:



This is at Houtman's:



And sometimes somebody else does the complete job (more or less):

[michael1954]

I'm getting new tires and can save a bunch of $ and get them put on much faster if I bring in the wheels without the bike. I'm a tad nervous about balancing on the center stand with 4x4s holding up the front and rear. Should I be worried. Really don't want to drop it in the garage.

Thanks

Funny you asked this question because I was going to do the same. I need to remove the front wheel on my DLX to replace the wheel that is overly corroded, at lease to me. Bike on center stand, with a floor jack under the front of the engine should keep it stable. Since I have roaming cats in and out of my garage, I feel the need to place something under the front forks.

I took both my wheels off to send them away to BartFactory to be made tubeless. I had some engine bars and car axle stands which made it very stable. See https://youtu.be/Yxr8lYkOOTA

Saw your use of jack stands on the crash bars. So glad I am a member of this Forum. I just need to install the ones I have in a box before I remove the front wheel. Great Video.

[Cormanus]

Django, where in the USA was this taken?

[Django]

That was the motorcycle doctor at Escalante/Utah.

That episode starts here and the page before:
http://cb1100forum.com/forum/showthread....#pid241764

Man, was that a good time....

[michael1954]

These are mine:





Well, that was a little bit more than tire change:



This is at Houtman's:



And sometimes somebody else does the complete job (more or less):

I thought I was the only one that covers his bikes with towels, sheets, blankets and T-shirts!

[Cormanus]

That was the motorcycle doctor at Escalante/Utah.

That episode starts here and the page before:
http://cb1100forum.com/forum/showthread....#pid241764

Man, was that a good time....

His shop reminded me of a dude who put a new tyre on Pterodactyl’s bike when we were in the US. That was a good time too …

http://cb1100forum.com/forum/showthread....6#pid94016