Login

holy666diver_imp · 12-07-2016, 02:34 AM

So I just installed the Arrow Slipon on my 2014 cb.

Anyone who has one I have a question. When I slipped it onto the headers there was about a 2cm gap between the end of the slip on and the end of the header connector. Meaning it didn't slip on 100% of the length of the header connector. There's no room for air to get in just curious is this is normal. With the clamp tightened I highly doubt any leaks would occur. If I do slip it on !00% of the length the mounting bolt does not align properly

My previous slipon the Yoshimure RS3 fit the entire length of the connector.

the Ferret · 12-07-2016, 02:35 AM

you have both pipes, maeasure the length of the connector pipe and see if the arrow is shorter.

holy666diver_imp · 12-07-2016, 02:38 AM

You know what I think I installed the arrow on the outside of the exhaust bracket instead of the inside... I'll re-install tonight see if that fixes it

holy666diver_imp · 12-07-2016, 04:28 PM

I installed the arrow exhaust on the back end of the bracket and now the exhaust fully fits. I fully tightened the bolt to the bike and tightened the clamp to the header. There seems to be a little bit of movement now even with the bolts fully tightened. Not enough to do any damage but is a little movement back and forth normal? Anyone with an arrow chime in?

Sent from my iPhone using Tapatalk

holy666diver_imp · 12-08-2016, 01:47 AM

See the movement? Could this be the clamp to the header is not getting tight enough? I am confused the previous exhaust I had did not move this much.

*MOD you can move this to "mechanical / Technical"

the Ferret · 12-08-2016, 02:00 AM

it looks like the movement is coming at the peg bracket mounting location to me. Is it rubber mounted?

holy666diver_imp · 12-08-2016, 02:03 AM

(12-08-2016, 02:00 AM)The ferret_imp Wrote: it looks like the movement is coming at the peg bracket mounting location to me. Is it rubber mounted?

All the stock hardware. Bolt and a rubber grommet inside. It's fully tightened.

the Ferret · 12-08-2016, 02:23 AM

The reason I asked, at the 14-18 second mark you can clearly see the peg mounting bolt moving up and down as you wiggle the pipe.

holy666diver_imp · 12-08-2016, 02:38 AM

(12-08-2016, 02:23 AM)The ferret_imp Wrote: The reason I asked, at the 14-18 second mark you can clearly see the peg mounting bolt moving up and down as you wiggle the pipe.

It's as tight as it gets. I'll strip it if I go any tighter. I can try adding another washer see if it tightens up.

the Ferret · 12-08-2016, 02:56 AM

Or just not worry about it. It's not going to fall off. Does it leak at the joint?

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	Exhaust system/slip-on	johnny_elpino_imp	26	1,762	05-26-2023, 01:06 AM Last Post: kzoorue_imp
	Arrow Slip-On Thoughts	le_penseur_imp	84	4,131	05-15-2023, 05:20 AM Last Post: mrded_imp
	Arrow exhaust.	Mixagon_imp	11	775	10-25-2022, 01:56 AM Last Post: ymtnpoah11_imp
	Arrow full exhaust	gretle_2.0	2	291	05-17-2022, 11:38 AM Last Post: GoldOxide_imp
	delkevik slip on mufflers	outback_imp	4	478	10-14-2021, 12:44 AM Last Post: outback_imp
	loose the arrow	jimgl3_imp	33	1,675	08-30-2021, 11:14 PM Last Post: the Ferret
	Delkevic Muffler slip-on	wgscheib_imp	2	304	06-08-2021, 01:48 AM Last Post: GoldOxide_imp
	Arrow slip on mufflers	DougsZ28_imp	15	1,038	05-13-2021, 04:09 AM Last Post: PowerDubs_imp
	CB1100 Noob Question re Slip-ons...	Whoops	15	852	04-23-2021, 06:07 AM Last Post: jimgl3_imp
	Arrow full system exhaust	tsmetjen_imp	19	1,117	07-29-2020, 03:46 PM Last Post: tsmetjen_imp

Threaded Mode Arrow Slip-on Question
Author	Message