Login

M3-SRT8_imp · 07-19-2015, 07:56 AM

Until it gets here, I was wondering whether I need to pick up anything extra to install it on the bike.

Stuff like exhaust sealant, gaskets, special tools, etc.

Do I need anything else?

Thanks. Huh

CB4ME_imp · 07-19-2015, 08:38 AM

Four header crush gaskets and a tool to remove the O2 sensor. I wouldn't think exhaust sealant is needed.

rboe · 07-19-2015, 08:50 AM

Have it shipped to my place. I'll figure it out for you. Then do some long term testing to make it's right. Angel

ChipBeck_imp · 07-19-2015, 09:31 AM

(07-19-2015, 08:38 AM)CB4ME_imp Wrote: Four header crush gaskets and a tool to remove the O2 sensor. I wouldn't think exhaust sealant is needed.

Gentlemen,

How does one remove the old crush gaskets? Those things are really stuck in there.

Chip

the Ferret · 07-19-2015, 10:38 AM

In the past I have used a pointed pick with a bent tip (like dentist might use for scraping tarter from between tour teeth) hook it on the inside and pop it out.

lash_imp · 07-19-2015, 10:52 AM

If you take a flat screwdriver and tap it with a small hammer, tip on the inside lip of the gasket, will put the gasket enough out of round that you can use a dental pick or such to pop it out. The gaskets are very soft and all you need is enough space between it and the head to get a pick in behind it.
I made my own O2 tool. Worked perfect.

M3-SRT8_imp · 07-19-2015, 11:20 AM

Thanks.

Any Torque Specifications I should use? Cool

lash_imp · 07-20-2015, 06:22 AM

Book says exhaust pipe joint nuts, headers to engine, is 16 ft/lb.

Toddman_imp · 07-20-2015, 06:29 AM

(07-19-2015, 09:31 AM)ChipBeck_imp Wrote:
(07-19-2015, 08:38 AM)CB4ME_imp Wrote: Four header crush gaskets and a tool to remove the O2 sensor. I wouldn't think exhaust sealant is needed.

Gentlemen,

How does one remove the old crush gaskets? Those things are really stuck in there.

Chip

Gentlemen,

How does one remove the old crush gaskets? Those things are really stuck in there.

Chip
A spring tool works great. Looks like a bent pick with a handle built in.

M3-SRT8_imp · 07-20-2015, 10:50 AM

Waiting, waiting... Cool

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	2017 CB and 1st gen Wyvern exhaust	sonnyb_imp	9	567	02-24-2019, 07:25 AM Last Post: lash_imp
	another exhaust thread-wyvern	sonnyb_imp	11	769	07-09-2018, 09:01 PM Last Post: lash_imp
	4-4 Exhaust Systems: Wyvern vs Endurance	M3-SRT8_imp	17	889	03-29-2017, 02:19 AM Last Post: AzBob_imp
	WHITE HOUSE AND WYVERN PICS	FJR919_imp	34	1,714	05-20-2015, 11:32 AM Last Post: FJR919_imp
	Wyvern install	lash_imp	7	445	05-20-2015, 06:15 AM Last Post: the Ferret
	Will a CB1100 single exhaust fit the dual exhaust mountings	Landy100_imp	1	207	05-02-2015, 09:44 AM Last Post: Randy B
	Wyvern Single Megaphone Exhaust System	Gumby 1100_imp	6	350	09-05-2014, 12:44 AM Last Post: pechorin75_imp
	anyone on the forum have the 4/4 wyvern exhaust	jamboa_imp	8	366	07-07-2013, 10:50 AM Last Post: HikerToo_imp
	R's Gear "Wyvern" 4-4 Exhaust	M3-SRT8_imp	12	639	06-02-2013, 07:21 AM Last Post: M3-SRT8_imp

Threaded Mode Wyvern 4-4 Exhaust On The Way...
Author	Message