Login

**Cormanus** · 03-26-2015, 02:38 PM

Thanks Gumby and Ferret. Thumbs Up

Hondadawg1_imp · 01-21-2017, 09:46 AM

(03-25-2015, 05:16 AM)Voitus_imp Wrote: Hi All,

Since I'm quite tall (192 cm) I've successfully installed 5cm (2 inch) ROX bar riser that pivots along its axis giving plenty adjustment options. The cables are long enough and the bar is now really higher.

Just sharing :-)

I am looking at these risers now. Did you have to modify the brake line, throttle cable or wiring ?

physics-teacher_imp · 01-21-2017, 12:25 PM

They will be stretched tight indeed, depending on how you position the bars, but I've done a few thousand miles with mine with no issues.

1100rider_imp · 01-23-2017, 03:23 AM

I also installed them on my CB and they give me a better riding position.

Dvassino_imp · 05-15-2017, 08:17 PM

Hello 1100rider,
Do you still have your rox risers installed?
How tight are the cables?
Thanks,
Dino

(01-23-2017, 03:23 AM)1100rider_imp Wrote: I also installed them on my CB and they give me a better riding position.

will866_imp · 05-22-2017, 02:29 AM

Installed my risers yesterday and went for a ride. Positive difference for me was drastic. No longer reaching out for handlebar and putting lots of weight on wrists. Really big improvement. Still messing with exact right position because there are so many options but very happy. They were very easy to install and brake lines are taught but fine.

Nightengale_imp · 05-22-2017, 03:15 AM

Interesting. I tried fitting the 2" Rox risers this weekend and failed. The front brake line is particularly short. I could have pivoted the line a bit (loosen the bolt on the master cylinder and angled the line downward) but it did not appear that this would be sufficient.

Did you reroute cables or lines? I'm thinking about selling the risers if I can't get these to work.

will866_imp · 05-22-2017, 10:31 PM

I did not. There was just enough slack. Maybe tilt risers forward at first until you have everything in place and lightly screwed down and then pull them back to comfortable riding position prior to final tightening. Having a second set of hands assisting definitely helped.

Nightengale_imp · 05-23-2017, 03:36 AM

Yep, did all that, had that (four hands). I measured the Rox's again and it seems they are 2 1/4" high. Maybe just a tad 'too much'. It's the front brake line that is the most noticeable problem. I did not loosen the bolt however, as it looked like it still would not be enough. May try again though, just to be sure.

Still working towards that 25 post count...

Lord Popgun · 05-23-2017, 03:42 AM

Go welcome some new members Nightengale...

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	FOBO tire pressure monitoring system report..	Chuckk_imp	120	7,636	11-28-2020, 10:38 AM Last Post: Chuckk_imp
	Handlebar riser	Ale72_imp	21	1,190	12-30-2019, 04:38 AM Last Post: lash_imp
	Options for handle bar riser	itstuantran_imp	1	294	06-21-2019, 03:49 AM Last Post: Bazbro_imp
	Low Bar (CB500) with Riser Flip - Perfect Sport Ergos	Ulvetanna_imp	32	2,222	06-17-2019, 12:19 PM Last Post: Cormanus
	INSTALLED: Rox Pivoting Riser 2" rise x 7/8 stem clamp x 7/8 " handlebar	Mandrau_imp	11	769	10-24-2018, 12:29 AM Last Post: Mandrau_imp
	I inch riser	Mscb1100_imp	12	929	10-16-2017, 10:58 PM Last Post: Mscb1100_imp
	Arrow full exhaust system report	daskraut_imp	3	340	05-15-2016, 10:43 PM Last Post: JF Coastal_imp
	Handlebar Riser Search	Motogeezer1949_imp	5	449	03-18-2015, 03:57 PM Last Post: JustPassinThru_imp
	Report on K&N Filters	CIP57_imp	28	1,690	10-02-2014, 12:07 PM Last Post: Dakota_imp
	Anyone have a Daytona Cozy Seat Report?	LiveToRide_imp	1	194	01-18-2014, 08:59 AM Last Post: CB4ME_imp

Threaded Mode ROX 5cm bar riser report
Author	Message