Login

Carguy1959_imp · 06-24-2016, 01:12 PM

Here is a picture of mine. I cut the snout off flush and drilled 3 1" holes. Then trimmed out th cap a bit.

Catbird_imp · 06-24-2016, 11:35 PM

(06-24-2016, 01:12 PM)Carguy1959_imp Wrote: Here is a picture of mine. I cut the snout off flush and drilled 3 1" holes. Then trimmed out th cap a bit.

What did you use to open the hole in the end cap? It's hard to tell from the picture, but it looks fairly uniform and finished (not butchered).

Carguy1959_imp · 06-25-2016, 10:58 AM

I used a demel with a cut off wheel. Cleaned up the edge with a die grinder

Catbird_imp · 06-25-2016, 10:29 PM

I don't think I could do as well as you did.

I was thinking about removing the end cap, inverting & stabilizing it on a piece of scrap wood and then using a hole saw of the desired diameter. (still thinking)

Biggin_imp · 07-03-2016, 09:42 AM

(06-20-2016, 12:11 PM)dsinned_imp Wrote: Biggin, so what you did is effectively allow a way for the exhaust to escape directly out of the eight drilled holes thru the existing hole in the end cap where the muffler's tail pipe use to stick out? And you did this based on how the sound improved while riding with the end cap removed? Please provide a photo of how it looks now. TIA.

Sound based on having it running and pulling the end cap off with fast idle, to me is pleasant improvement have no thoughts of buying muffler now. Going to spend money on k & h seat
Sorry no pic, someone posted the same as my looks
Thanks. Oh by the way I hear no popping on decel

dsinned_imp · 07-03-2016, 01:37 PM

I was very tempted to follow your lead, but decided to go with an aftermarket slip on instead. This way I can always go back to 100% stock, which may be important if I ever sell the bike.

Outlander427_imp · 07-17-2016, 04:57 AM

I'm planning on doing this. I can't tell for sure but it appears that you cut off the outlet in addition to drilling the holes. Is this the case?

TCinNC_imp · 07-17-2016, 10:29 AM

(07-17-2016, 04:57 AM)Outlander427_imp Wrote: I'm planning on doing this. I can't tell for sure but it appears that you cut off the outlet in addition to drilling the holes. Is this the case?

You don't have to cut off the outlet. The OP just drilled holes in the end of the muffler with the end cap removed, and then re-installed the end cap (just as I did as well).

darkangel_imp · 10-31-2016, 04:28 AM

Hi, have anyone done this mod on 2104 cb1100 DLX? It seems the end of 2014 exhaustes are difference and I don't know how to open them. Please post a guide if youhave done it. Thanks!

CBryder_imp · 11-15-2016, 10:43 AM

So there I was with the drill in my hand for an unrelated project. What the he**! 6 x .5

Louder than I expected, but I'm sure it'll grow on me.

Sent from my SM-G920T using Tapatalk

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	Stock Mirrors	MrBob_imp	5	533	04-11-2025, 03:33 AM Last Post: balkanhound_imp
	Stock Muffler	jbird06_imp	8	712	05-02-2024, 11:21 AM Last Post: PowerDubs_imp
	Stock exhaust or aftermarket header?	milkmaster_imp	17	1,315	07-20-2023, 04:11 AM Last Post: mvk24_imp
	Decat stock pipes	ozigoo	4	460	05-22-2020, 10:55 AM Last Post: peterbaron
	Stock vs. aftermarket exhaust	LongRanger_imp	15	1,017	11-30-2019, 06:30 AM Last Post: GoldOxide_imp
	Shaved Stock or K+H Low	GroovyBunny86_imp	18	1,461	06-18-2019, 12:58 AM Last Post: BayAreaRick_imp
	Modify stock muffler?	DBM_imp	2	336	07-30-2018, 05:08 PM Last Post: FLYTYM_imp
	Anybody modify a stock 014' seat?	el duque_imp	9	680	06-05-2018, 03:39 PM Last Post: el duque_imp
	stock seat mod	TCBronson_imp	6	618	10-03-2016, 06:19 PM Last Post: ryanschillinger_imp
	Stock Honda Rack	Frulk_imp	14	1,008	08-07-2016, 07:35 PM Last Post: curlyjoe

Threaded Mode Stock Exhaust Mod
Author	Message