Posts: 9
Threads: 1
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Sep 2015
"spin the dang cam around where it ain't contacting the lobe."
True enough, that separates the Top Dead Center compression stroke from TDC exhaust or two rotations of the crankshaft per full cycle
"the cam lobe is contacting the valve or it isn't. "
Maximum full open is not just open even for intake readings. Do not rotate in reverse to find it.
Posts: 163
Threads: 6
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Mar 2015
(10-31-2015, 04:25 AM)Birddogvet_imp Wrote: "spin the dang cam around where it ain't contacting the lobe."
True enough, that separates the Top Dead Center compression stroke from TDC exhaust or two rotations of the crankshaft per full cycle
"the cam lobe is contacting the valve or it isn't. "
Maximum full open is not just open even for intake readings. Do not rotate in reverse to find it.
Have you ever checked the valves on a shim under bucket valve train? When the lobe is pointing away from the valve, take the minimal shim clearance feeler and if it slides in, you're good. I don't see any reason to go to TDC to check any of the valves. The cam should be true all the way around until it hits the lobe.
Posts: 9
Threads: 1
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Sep 2015
"Have you ever checked the valves on a shim under bucket valve train? "
I stand corrected.
Posts: 915
Threads: 66
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: May 2014
Lee finished my valve check Saturday. Cylinders 1 & 2 were fine, 3 was loose on the exhaust, 4 was loose on both intake and exhaust. None of them out by very much.
He said the shims are the same as the Yamaha R6 uses.
Posts: 8,035
Threads: 21
Likes Received: 186 in 108 posts
Likes Given: 136
Joined: Apr 2025
Moto,
Did they give you the numbers? Would be nice to see some actual data.
Posts: 23,432
Threads: 697
Likes Received: 512 in 234 posts
Likes Given: 676
Joined: Apr 2025
Hmmm I thought the skinny on this type of valve arrangement was that they got tighter with wear, not looser?
Posts: 1,214
Threads: 71
Likes Received: 113 in 31 posts
Likes Given: 16
Joined: Apr 2025
(11-02-2015, 11:32 AM)The ferret_imp Wrote: Hmmm I thought the skinny on this type of valve arrangement was that they got tighter with wear, not looser?
So it is.
Posts: 241
Threads: 27
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: May 2013
(10-29-2015, 05:10 AM)AzBob_imp Wrote: (09-11-2015, 04:27 AM)12cb96vfr_imp Wrote: well.................I'm a moron!!! hahaha my buddy just called me and said all the valves are spot-on 100% perfect. I guess i was checking them wrong, b/c he said everything is good to go!
All in all I'm glad I checked, at least I know I'm all set now.
Question: when you checked them (incorrectly), did you follow the procedure in the Honda shop manual? Because that's how I'm planning to do it and now I'm kind of worried that I might mess it up.
Question: when you checked them (incorrectly), did you follow the procedure in the Honda shop manual? Because that's how I'm planning to do it and now I'm kind of worried that I might mess it up.
sorry man I've not been on here much - yes I did (at least i thought I did haha), BUT I've never done it before so I'm sure I was doing it wrong. It was my first time doing shim under bucket valves so I guess I was doing something bass ackwards
Posts: 915
Threads: 66
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: May 2014
Pop, they is my buddy Lee, lifetime Honda mech. The next size up shims, whatever they are.
Ferret, without baselining, your postulation can't be known. Next time, we'll have something to compare to.
I just ride 'em, I leave the technical stuff to Lee. I have a detail guy too. 'Cause I'd rather be leanin' than cleanin'
Posts: 1,214
Threads: 71
Likes Received: 113 in 31 posts
Likes Given: 16
Joined: Apr 2025
I had my CB to the 24,000 km service today. Valves were checked and all are in spec.
There were some minor differences to the measurements of the 12,000 km service, which I suppose to be more or less measurement errors.
However, those iridium spark plugs, which should be changed every 24,000 km are really expensive! One is 45 € (49 USD).
