Login

Southwend · 09-19-2015, 11:13 AM

Once you start changing the exhaust back pressure don't you start down the road of changing the intake and the chip?

Does the bike adapt its state of tune to the new parameters?

Carguy1959_imp · 09-19-2015, 11:46 AM

Good question, I have wondered the same thing.

Brookland27_imp · 09-20-2015, 10:32 AM

The bikes onboard ECU can compensate for small changes in flow (saying "backpressure" makes it seem like that's what the motor wants.. it doesn't) most people get by without retune fueling when simply putting on an open flow silencer even. I can tell you from experience though that the bike will run noticeably lean <5k revs without a power commander. I installed the power commander with the supplied stock tune and it runs so much better in the commonly used power region. I actually think the sound of the pipe actually just accentuates or makes more apparent the lean state the bike is delivered with. When you cant hear it you just feel flat. As far as changing the intake is concerned that is another ballgame but the motor can only put out what it intakes so freeing up outflow doesnt require any chang e in intake only fueling. But that's another thread .

Carguy1959_imp · 09-21-2015, 10:07 AM

Brookland, is there more than one "power commander"? And where did you get yours?
Thanks....

Southwend · 09-26-2015, 02:24 AM

I had staintune on my Thruxton, very nice. When i can afford the outlay an option for sure. Has anyone tried to drill a small hole in the stock baffle for just a bit of sound? Maybe 1/4" or less. Is this a bad thing for any mechanical reason? Will it even make a slight db difference?
oh yeah and another thing I have noticed a couple of slip-ons on samurider site Striker and Moto Gear slip ons, both about 60,000 yen. Anyone tried either?

the Ferret · 09-26-2015, 04:53 AM

(09-26-2015, 02:24 AM)southwend_imp Wrote: I had staintune on my Thruxton, very nice. When i can afford the outlay an option for sure. Has anyone tried to drill a small hole in the stock baffle for just a bit of sound? Maybe 1/4" or less. Is this a bad thing for any mechanical reason? Will it even make a slight db difference?
oh yeah and another thing I have noticed a couple of slip-ons on samurider site Striker and Moto Gear slip ons, both about 60,000 yen. Anyone tried either?

Southwend, read this thread

http://cb1100forum.com/forum/showthread....ht=Gutting

Southwend · 09-26-2015, 12:08 PM

(09-26-2015, 04:53 AM)The ferret_imp Wrote:
(09-26-2015, 02:24 AM)southwend_imp Wrote: I had staintune on my Thruxton, very nice. When i can afford the outlay an option for sure. Has anyone tried to drill a small hole in the stock baffle for just a bit of sound? Maybe 1/4" or less. Is this a bad thing for any mechanical reason? Will it even make a slight db difference?
oh yeah and another thing I have noticed a couple of slip-ons on samurider site Striker and Moto Gear slip ons, both about 60,000 yen. Anyone tried either?

Southwend, read this thread

http://cb1100forum.com/forum/showthread....ht=Gutting

Southwend, read this thread

http://cb1100forum.com/forum/showthread....ht=Gutting

(09-26-2015, 04:53 AM)The ferret_imp Wrote:
(09-26-2015, 02:24 AM)southwend_imp Wrote: I had staintune on my Thruxton, very nice. When i can afford the outlay an option for sure. Has anyone tried to drill a small hole in the stock baffle for just a bit of sound? Maybe 1/4" or less. Is this a bad thing for any mechanical reason? Will it even make a slight db difference?
oh yeah and another thing I have noticed a couple of slip-ons on samurider site Striker and Moto Gear slip ons, both about 60,000 yen. Anyone tried either?

Southwend, read this thread

http://cb1100forum.com/forum/showthread....ht=Gutting

Southwend, read this thread

http://cb1100forum.com/forum/showthread....ht=Gutting
I loioked at it Yikes what a rube goldberg way to muffle. I am trying to resist the temptation to fix the unbroken. It would be nice for just a bit more sound but it is so nice just as it is...

Carguy1959_imp · 10-03-2015, 12:16 PM

Here is the final pictures of my factory exhaust mod. I opened the end cap, I think that made the most difference in it having a deeper sound. I cut the inner snoot off flush with backing plate. Then I drilled 3 1 inch holes in the plate. My bike a a nice rumble thru the rpm range. I don't know how to post a sound clip. I have one on my I pad but it would let me post it.
And the cap

Ralph_imp · 10-26-2015, 01:06 AM

Modified FLH with shop fabricated baffles:

a1walt_imp · 10-26-2015, 10:57 AM

Stock here. I like to sneak up on people.

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	Smaller turn signal/running light choices	TxRonHarris_imp	33	2,046	07-06-2021, 10:00 PM Last Post: mvk24_imp
	Killing the Buzz - Installing "Even Running" Cam?	M3-SRT8_imp	8	598	08-02-2020, 03:17 AM Last Post: M3-SRT8_imp
	Attaching led strip light to running light?	The Beast J7_imp	6	527	06-28-2018, 12:58 PM Last Post: The Beast J7_imp
	Poll: Limited or black 2017 tank?	Ferrealls_imp	20	1,226	04-10-2018, 06:07 AM Last Post: the Ferret
	Added Denali Running Lights	Mscb1100_imp	3	368	03-27-2018, 12:39 PM Last Post: Mscb1100_imp
	For those running heated grips...	Guth_imp	11	635	02-08-2018, 06:22 AM Last Post: Acrobat_imp
	LED running lights installed	Matt F._imp	2	253	02-09-2017, 06:46 AM Last Post: Matt F._imp
	Rear turn signal conversion to Running lights?	kenfyoozed_imp	4	342	03-18-2016, 01:28 AM Last Post: Toddman_imp
	What size tires are you running?	Ferrealls_imp	4	336	05-29-2015, 02:15 PM Last Post: rboe
	Will a CB1100 single exhaust fit the dual exhaust mountings	Landy100_imp	1	234	05-02-2015, 09:44 AM Last Post: Randy B

Threaded Mode Poll: What kind of exhaust are you running?
Author	Message