Posts: 249
Threads: 37
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Jul 2014
So i did my oil and chain this week end. I needed to tighten up my slack so I did as I usually do.
Loosen axle nut
adjust left and right adjusters one at a time equal truns.
Check slack.
I was at an inch on the slack and at 3 1/2 notches on each side of the chain adjuster.
I then tightened the axle nut and torqued to 69 lb ft.
I noticed the right side chain adjust screw can be loosened by hand after the axle was locked in place. It doesn't effect anything since the axle is locked but is it normal to have that adjuster be able to rotate by turning with your finger? left side with the chain on it is tight
Posts: 1,209
Threads: 71
Likes Received: 88 in 25 posts
Likes Given: 14
Joined: Apr 2025
(03-27-2017, 01:50 AM)holy666diver_imp Wrote: So i did my oil and chain this week end. I needed to tighten up my slack so I did as I usually do.
Loosen axle nut
adjust left and right adjusters one at a time equal truns.
Check slack.
I was at an inch on the slack and at 3 1/2 notches on each side of the chain adjuster.
I then tightened the axle nut and torqued to 69 lb ft.
I noticed the right side chain adjust screw can be loosened by hand after the axle was locked in place. It doesn't effect anything since the axle is locked but is it normal to have that adjuster be able to rotate by turning with your finger? left side with the chain on it is tight
No. I'd say, the right end of the axle moved a little bit back by tightening the axle nut. That released the right chain adjuster.
Posts: 23,403
Threads: 697
Likes Received: 482 in 220 posts
Likes Given: 596
Joined: Apr 2025
Axle probably moved forward slightly (moving away from the adjuster) as the axle nut is tightened clockwise. It will really be insignificant so just snug up the adjuster as chain slack should still be in spec.
Posts: 16,116
Threads: 342
Likes Received: 664 in 364 posts
Likes Given: 773
Joined: Apr 2025
As I recall, the user manual says to re-check the tension after you've tightened the axle nut and snug up the adjuster.
Posts: 547
Threads: 14
Likes Received: 11 in 8 posts
Likes Given: 9
Joined: Apr 2025
(03-27-2017, 11:03 AM)Cormanus_imp Wrote: As I recall, the user manual says to re-check the tension after you've tightened the axle nut and snug up the adjuster.
+1 Snugging up the adjuster screws when you're all done is key. Mine was coming out of adjustment by 1/8 to 3/8 when I checked it a few rides later. Yep, I set the tension right and torqued the axel nut to 2013 spec. Drove me nuts until I started to snug the adjusters up - keeps the chain adjustment rock solid
Posts: 249
Threads: 37
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Jul 2014
Snug it up it is! I must have missed that step
Posts: 6
Threads: 1
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Aug 2013
I like using the chain alignment tool from Motion Pro. Helps me keep it straight if I happen to get one side off from the other.
Posts: 933
Threads: 17
Likes Received: 12 in 6 posts
Likes Given: 11
Joined: Apr 2025
That's what I have. Got it for a gift and it works pretty well.
Posts: 288
Threads: 20
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: May 2015
A trick to making sure your that the axel is being forced back against the adjuster before tightening the axel bolt is to put a screwdriver shaft or something similar into one of the teeth on the sprocket and then rotate the wheel until tension is created by the screwdriver. Then tighten the nut and re-check the slack. Works like a charm. There are some videos showing this on youtube.
