in need of opinions

[HikerToo_imp]

Moriwaki skid pads here, was going to get Honda OEM ones( and I checked, same part number for 2013 as 2014), but these came up used on the forum so bought instead.

http://www.samurider.com/?p=4221

[Gumby 1100_imp]

I went with black SW-Motech case savers from Twisted Throttle. Visually they are hidden on the bike and are very stout. Have not tested them yet; but they do make it easy to right the bike if you lay it down. I tested this feature in my back yard on the lawn.

The SW-Motech have my vote too and I installed them for similar reasons. They seem very substantial and much more likely to protect the engine casings in the event of a tip-over.

The Honda guards look nice but the mounting brackets seem very flimsy and are much more likely to fold over under pressure. They are, in my opinion, more bling than brawn.

[Rocky_imp]

I went with black SW-Motech case savers from Twisted Throttle. Visually they are hidden on the bike and are very stout. Have not tested them yet; but they do make it easy to right the bike if you lay it down. I tested this feature in my back yard on the lawn.

I did too and I like the look very much.
Easy to install and they look great.
No plans to test them though

[jsinher3_imp]

Be careful what you buy, a member here had a set put on that stood him up across lanes and ended up in a ditch, can't remember the thread or the type of guards.

its the kijima

Be careful what you buy, a member here had a set put on that stood him up across lanes and ended up in a ditch, can't remember the thread or the type of guards.

See [url=http://cb1100forum.com/forum/showthread.php?tid=3172&pid=45520#pid45520]here.

See [url=http://cb1100forum.com/forum/showthread.php?tid=3172&pid=45520#pid45520]here.
just read it, thats a little scary.

[CB4ME_imp]

I had the Active guards. The way they angle up from the bottom, there's no worries they will be the first point of contact in a lean. I switched to SW-Motech guards for a more subdued look. As has been said, they are heavy duty!

[jsinher3_imp]

I put R&G sliders on mine.

We just received our Honda guards. I found them on eBay at a dealer/shop in Fl.
I went to their website and ordered them direct.
$180.00, free shipping. I can post a link to them later if anyone wants it.

i think i might have found it in servicehonda.com

I went with black SW-Motech case savers from Twisted Throttle. Visually they are hidden on the bike and are very stout. Have not tested them yet; but they do make it easy to right the bike if you lay it down. I tested this feature in my back yard on the lawn.

thanks for that information

Moriwaki skid pads here, was going to get Honda OEM ones( and I checked, same part number for 2013 as 2014), but these came up used on the forum so bought instead.

http://www.samurider.com/?p=4221

i also found these







i was also thinking of combining the agrass sliders with the Black Moriwaki pegs sorta like the above picture.

[Papa Weeley_imp]

I've got the Moriwakis, too.
I had them previously on an FZ1, and liked how they "blended into the scenery" - which I like even more on my mostly-stock-looking CB - yet still give some protection.
Check it out, you can hardly tell they're there:
[url=http://s157.photobucket.com/user/mustangfeverrr/media/f5c0325a-0ba3-458a-b886-b80051175d51_zps23f8d10a.jpg.html]

[jsinher3_imp]

I've got the Moriwakis, too.
I had them previously on an FZ1, and liked how they "blended into the scenery" - which I like even more on my mostly-stock-looking CB - yet still give some protection.
Check it out, you can hardly tell they're there:
[url=http://s157.photobucket.com/user/mustangfeverrr/media/f5c0325a-0ba3-458a-b886-b80051175d51_zps23f8d10a.jpg.html]

thanks for the pic i looked at other ones on the web and they seem tiny, but in this pic they are a decent size. do you happen to know how far past the case cover they extend? i am thinking of going with these and the agras cover slider.
the trex ones look good too butt they look kinda eh.

[Papa Weeley_imp]

Yeah, they're actually pretty beefy.
I'd say they extend maybe 3/4"-1". That doesn't sound like much, but they protrude out far enough that the bike would definitely pivot on them instead of the case if it fell over.
It's more than it looks in either of these pics, but this might give you a bit of the idea:
[url=http://s157.photobucket.com/user/mustangfeverrr/media/024_zpsb07bfe41.jpg.html]

[jsinher3_imp]

Yeah, they're actually pretty beefy.
I'd say they extend maybe 3/4"-1". That doesn't sound like much, but they protrude out far enough that the bike would definitely pivot on them instead of the case if it fell over.
It's more than it looks in either of these pics, but this might give you a bit of the idea:
[url=http://s157.photobucket.com/user/mustangfeverrr/media/024_zpsb07bfe41.jpg.html]

thanks, this pic helped a lot i think im going with these over the bar style guards.