Honda Project bike thoughts?

[Gone in 60]

Hey bflint, I was in the same boat as you once. I wanted to shake things up a bit and buy a bike to wrench on, and found a '93 Nighthawk. I put it back in perfect OEM condition and rode it for a few years before passing it on. I figured that was a nice, simple bike that would either make me want to restore more bikes, but I got my jollies on that one, and have just taken care of my small rotating fleet since then.

As others have said, the carbs needed a good cleaning, and I got some great tips from friends on making them sing. Why do I think there are more project CX500s now than CX500s actually made? My friend showed up on one recently.

And, shameless plug, if you still have that Nighthawk, and it's Tahitian Blue, I have a new OEM right side panel for one if you are interested.

[GoldOxide_imp]

[url=https://www.youtube.com/watch?v=7ZEbymkexWQ]

[FLYTYM_imp]

If you have no previous project bike experience, you might want to consider starting with something smaller, and relatively more simple. For example something in the mini trail series of Honda bikes, Z50 or CT70. All the basic principles will be the same as in larger bikes, it will still be challenging/rewarding as an experience, but also easier to handle as a first time project.

Might want to look past the 50-CT70 Honda’s,prices for these thing are insane. I’ve got an early CT70 that I was restoring but until I can secure my garage to keep some looser from stealing it I’ve put it on hold. Fully restored examples are going for $7000+,this for a minibike that was less than $400 new.

[pekingduck]

Love my `14 CB1100DX, but looking for some additional entertainment. Thought about getting a Honda project bike to inspire and aggravate me. When I just got back into cycle in 2015, bought a unblemished `93 750 Nighthawk that went directly to cycle shop for 6 months of repairs … bought my CB1100 while waiting the 6 months. I only did a little scavaging for the 750, so I really have no project bike experience.
*
Anybody have any suggests for where to look for a project bike and what model? Love the v45 and v65 and cx500, but not many around. Thought maybe something between 400cc and 900cc, but guess anything could work. Probably most expensive thing will be tools, plus have to kick my wife out half the garage … its mine right ?

Before we saddle you with a huge project, wondering what might be your skill level, what you plan to do with it, modify or keep it stock.

[Chuckk_imp]

didn't some of those cx500's have water pump troubles.. I barely can remember.. I had a couple of them ..

here are two of my little cx500's..
.
.[/b]

[jimgl3_imp]

I am going to second the Honda goldwing 1000's and 1100's suggestion. An older fellow pulled up one day when I was out with my Harley crew. He was on an old Goldwing, and was as proud as a peacock! If I recall correctly, he had about $40 in a 4 carb rebuild kit.

[GoldOxide_imp]

didn't some of those cx500's have water pump troubles.. I barely can remember.. I had a couple of them ..

here are two of my little cx500's..
.
.[/b]

A nice perspective shot Chuck.

[bflint]

Thank you everyone! Love all the input and advice ... knew that many folks on this forum are cycle gurus ... and thanks for the pretty CX500 pictures (they did have some problems with the plastic composite fan blades cracking and causing funny noises). I think everyone's opinion/comments have value ... it just I did not really provide you folks with my perspective .. eg, I am not really into for reselling but don't want to invest a fortune either. Also, I grew up in my dad's small aircraft repair shop (Flint Aero) so mechanical stuff doesn't really intimidate me, plus I did do a complete tear down and rebuild of my 1964 Plymouth Valiant slant six engine in 1973 ... it did not need it but hey when your 17 in auto shop you need a project .. right? However ... I would be starting from scratch at this point in my life. I have no tools (except for wood working), no local machine shop contacts, and I need to develop some restoration contacts (for parts and knowledge). I am ok with that. Now what do I tell the wife ...

[Houtman_imp]

Tell your wife that you do it for her ! (getting out of the house )

[Chuckk_imp]

this guy knows his way around older goldwings .. sells his own parts, has his own manual.. corrects mistakes made in other manuals.. has a school, if I remember.. the real deal, if you decide to go down that goldwing road.. randakk website is the place to look ..
.