Road Comet Windshield annoying vibration NOISE!

[Riko_imp]

Hi all!

Yesterday I installed my Chic Design Road Comet I screen.
Smoke aero version.







Installation was not as easy as I expected, but still less fiddly than the rear OEM rack

That same night I took off, at night in the pouring rain, I didn't care
I really wanted to ride since the bike sat more than a week in the garage because of rain in combination with salty roads...but hey the temps went up past week and the rainy days flushed the salt away (I hope).

It was only city riding, so I could't really judge the screen.

However, I immediately noticed the screen made a very annoying vibration noise as soon as I revved the engine.
It didn't took much revving, relaxed riding was enough for the noise to appear!

I did see that Dengie Boy added these additional support brackets

But thats was because the screen bounced around at anything over 60mph...

But I think this would fix my noise issue as well since the noise went away when I pushed the screen a bit forward.

Do other owners experience the same issue?


Thx!

[Lord Popgun]

A number of us noticed a vibrating noise, especially after installing a screen. Turned out to be the connectors in the headlight shell vibrating against the bucket and/or headlight carrier (or whatever it's called

I wrapped my connector's with some thin foam sheeting I had laying around and no more vibration noise. Maybe that's your problem. Good luck

Ok here is a link to the pics I took. After I posted them, I went back and wrapped ALL the connectors and made it look a little better.

http://cb1100forum.com/forum/showthread....9#pid87099

[ChipBeck_imp]

Hi all!

Yesterday I installed my Chic Design Road Comet I screen.
Smoke aero version.







Installation was not as easy as I expected, but still less fiddly than the rear OEM rack

That same night I took off, at night in the pouring rain, I didn't care
I really wanted to ride since the bike sat more than a week in the garage because of rain in combination with salty roads...but hey the temps went up past week and the rainy days flushed the salt away (I hope).

It was only city riding, so I could't really judge the screen.

However, I immediately noticed the screen made a very annoying vibration noise as soon as I revved the engine.
It didn't took much revving, relaxed riding was enough for the noise to appear!

I did see that Dengie Boy added these additional support brackets

But thats was because the screen bounced around at anything over 60mph...

But I think this would fix my noise issue as well since the noise went away when I pushed the screen a bit forward.

Do other owners experience the same issue?


Thx!

Riko,

I've got a RC1 with both screens. As others have reported here the touring screen doesn't work real well on the RC1. It creates a lot of buffeting and turbulence at helmet level. My CB11 is a lot more comfortable with the standard screen on it. To stop the buzzing first tape up all of the connectors in your headlight shell. Make sure your instruments are not touching the fairing, and tape the outside of your headlight bucket where it contacts the opening in the fairing. And trust me, you'll be much happier with the standard screen and it looks better too. Cheers.

Chip

[Riko_imp]

How come these contacts all of a sudden became buzzy?
Just by replacing the 2 headlight bolts affected the inside of the headlight?


Am gonna test the screen today on the freeway.
I'm 1m83, whats your length?

Thx for the toptip

[silenthedges_imp]

Hi all!

Yesterday I installed my Chic Design Road Comet I screen.
Smoke aero version.







Installation was not as easy as I expected, but still less fiddly than the rear OEM rack

That same night I took off, at night in the pouring rain, I didn't care
I really wanted to ride since the bike sat more than a week in the garage because of rain in combination with salty roads...but hey the temps went up past week and the rainy days flushed the salt away (I hope).

It was only city riding, so I could't really judge the screen.

However, I immediately noticed the screen made a very annoying vibration noise as soon as I revved the engine.
It didn't took much revving, relaxed riding was enough for the noise to appear!

I did see that Dengie Boy added these additional support brackets

But thats was because the screen bounced around at anything over 60mph...

But I think this would fix my noise issue as well since the noise went away when I pushed the screen a bit forward.

Do other owners experience the same issue?


Thx!

Yes very nice couple your black fairing with my silver fairing!

[Riko_imp]

let me know if you also have the irritating zooming noise when you ride

[Chapomis_imp]

let me know if you also have the irritating zooming noise when you ride

None with my RCII. No tape, no foam

[Riko_imp]

hmmm, tape, foam, none of those would help

I removed the fairing and opened up the headlight case and I could not believe taping up all those cables as some advised is a solution for the ticking noise...

So I tackled the screen and I remembered the screws at the ears of the fairing have rubber bushings, but not the centre screw at the bottom.

This could be the reason.
So I added a rubber spacer between the horn assembly and the fairing bracket:
[url=https://picoolio.net/image/IdGK]
[url=https://picoolio.net/image/IdGW]
[url=https://picoolio.net/image/IdQ3]

I also made sure the horns did not touch the fairing....I cannot remember if they touched the fairing on my first install, so this could be the reason for the noise as well.

Whatever the reason, the annoying vibration noise is gone!!
No foam, no tape, no nothing!

[Lord Popgun]

If you can fit a piece of rubber in there, I would say you didn't have it installed correctly as the little bracket should fit tight against the horn brackets.

Interestingly, my RC bracket fits turned the other way from yours, and I used the original Acorn nut, albeit with a thin washer. The washer may have come with it or was OEM, but I can't remember.

The connector noise in the headlight bucket was more of a buzzing. Not a ticking noise. But I'm glad you found it and fixed it!!

[Riko_imp]

But it did fit tight against the horn bracket without the rubber...there is enough thread left for a thin piece of rubber.

Next update:normal screensize, since the Aero screen makes too much wind noise :/