Posts: 7,093
Threads: 94
Likes Received: 585 in 320 posts
Likes Given: 980
Joined: Apr 2025
(11-20-2018, 12:29 PM)The ferret_imp Wrote: Lol no but laying it down on the right hand side and crushing those 3 mufflers might prove to be expensive. I imagine an oem replacement set of those would be more than a few grand.
Minimum$::
https://www.britishbikebits.com/silencer...ricane-x75 +
https://www.britishbikebits.com/front-ex...-hurricane
Posts: 12,677
Threads: 77
Likes Received: 3 in 3 posts
Likes Given: 0
Joined: Dec 2014
Posts: 7,093
Threads: 94
Likes Received: 585 in 320 posts
Likes Given: 980
Joined: Apr 2025
Posts: 12,677
Threads: 77
Likes Received: 3 in 3 posts
Likes Given: 0
Joined: Dec 2014
(11-20-2018, 01:09 PM)peterbaron_imp Wrote: error
I don't understand, didn't you just post this link?
https://www.britishbikebits.com/silencer...ricane-x75
Indeed, yes. In any case, these would definitely see earth quickly.
Posts: 23,479
Threads: 697
Likes Received: 599 in 266 posts
Likes Given: 775
Joined: Apr 2025
Reproduction pipes are one thing, oem or a set of original equipment pipes would be something else I would assume. Maybe unobtainium.
Posts: 12,677
Threads: 77
Likes Received: 3 in 3 posts
Likes Given: 0
Joined: Dec 2014
Ah well, PB did a fine job. Hey! The claim on the link says they are Made In England.
Posts: 7,093
Threads: 94
Likes Received: 585 in 320 posts
Likes Given: 980
Joined: Apr 2025
(11-20-2018, 01:21 PM)GoldOxide_imp Wrote: (11-20-2018, 01:09 PM)peterbaron_imp Wrote: error
I don't understand, didn't you just post this link?
https://www.britishbikebits.com/silencer...ricane-x75
Indeed, yes. In any case, these would definitely see earth quickly.
I don't understand, didn't you just post this link?
https://www.britishbikebits.com/silencer...ricane-x75
Indeed, yes. In any case, these would definitely see earth quickly.
yes , I did and corrected due to misspell
Posts: 107
Threads: 14
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Aug 2015
Ok thanks everyone. I take away that the boxer layout is not a big deal.
Posts: 3,454
Threads: 129
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Jul 2015
Depends on who you ask. Lots of BMW aficionados will defend the design religiously, and others will be indifferent. It's no different from fans of other brands. Personally, I don't view the boxer layout as a significant feature or must-have. As I suggested earlier, try one before you swallow the Kool-Aid. You may find it's not for you.
Posts: 666
Threads: 43
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Jun 2014
As other's have said, no big deal if you lay it over. I owned a 1200GS I bought used and it had some nice little valve cover covers. When I went to check my valves on that bike, I pulled the covers off the valve covers and found some nice little scratches hiding under there. The rest of the bike, assuming no parts had been replaced, were unscathed. It was obviously a very low or no speed tip, so likely no other damage was done. There in lies an advantage of the boxer design. It often protects the rest of the bike from further damage since those cylinder heads allow the bike to rest and something close to a 45 degree angle. This also makes it much easier to pick back up.
This orientation also lowers the COG of the bike making it handle better and easier to ride at slow speeds.
One disadvantage, to my ear anyway, is the exhaust note. I always thought it sounded a bit "flatulant" and agricultural. Some find it quirky and enjoyable in it's own way. They aren't wrong. I've always admired the sound of a nice, prominent fart!