Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Making closed end grips work on the CB
Author Message
Skypilot_imp Offline
First Service Completed


Posts: 43
Threads: 8
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Mar 2019
Making closed end grips work on the CB
#1



So one of the more frustrating things that I’ve found so far with the CB 1100 is a lack of good looking grips out there. Most of what I have found wasn’t impressing me style wise. So I decided to give it a shot with a pair of good looking Renegades from Biltwell. Of course we have the bar and weights to deal with and the majority of the grips that are out there are closed end as opposed to our open and grips. But for $20 I figured I’d have a shot at making them work. I’m not a slave to style but I like my bikes to ride AND look a certain way. I have the steps show below with some pics to go along. Very easy project with a couple of tricks. Disclaimer here is that you will be boring a hole in these grips rendering them useless if you mess them up.


1. Take your choice of grips and bore a 3/4 hole in the closed end. I used a 3/4 hole saw and worked great. DONT use a regular drill bit and make sure it’s centered (obviously).


Here is the hole bored through the closed end



Take the bar end weight and push it through the hole you just made to make sure it fits

Take out the weight and install the grip on the bar. Here is the view from the end


The rest is easy just install the weight with the factory screw and seat the grip until it looks right.


The only issue with most grips is that they are a little short on the throttle side and there will be a gap between the grip and the control pod. I painted mine with black auto touch up paint from Autozone. DO THIS BEFORE YOU INSTALL THE GRIPS to avoid getting paint on your grips. It sticks out pretty badly if you leave it unpainted.
.


*****FYI the throttle sleeve extends about 1/4 inch beyond the end of the bar making the grip seem even shorter when installed. I don’t have a pic of this part and I don’t normally condone messing with throttles in any way but I took a dremel and sliced off about an 1/8 inch from the overhang in order to allow the grip to fully cover the throttle sleeve.



Sent from my iPhone using Tapatalk


05-17-2019, 09:40 AM
Find Reply


Messages In This Thread
Making closed end grips work on the CB - by Skypilot_imp - 05-17-2019, 09:40 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  Fork Gaiters and Heated Grips tdbru 20 2,929 05-02-2025, 11:16 PM
Last Post: Cormanus
  Spare connectors/Oxford heated grips White Dog_imp 13 1,439 04-18-2025, 10:02 AM
Last Post: peterbaron
  Finally making some progress............. FLYTYM_imp 19 1,463 07-18-2021, 01:49 AM
Last Post: FLYTYM_imp
  “Katsumi” - a new project in the making Zee9_imp 18 1,254 06-22-2021, 02:33 AM
Last Post: emptysea
   HEATING GRIPS ICON HONDA ORIGINAL NON-OPERATING CB1100 ex 2015 EUROPE. COMPLAINT TO Alfgaxatico_imp 16 1,807 12-10-2020, 07:35 AM
Last Post: Alfgaxatico_imp
  hand guards and heated grips misterprofessionality 33 2,272 11-16-2020, 10:06 AM
Last Post: mrded_imp
  thicker grips active1951_imp 15 1,164 08-04-2020, 12:55 PM
Last Post: gmike_imp
  Turn signal relocation -- Making room for my backseat rider JMA_imp 13 1,005 06-15-2019, 12:44 PM
Last Post: QUINTtastic_imp
  Custom paint and body work pricing misterprofessionality 3 461 04-30-2019, 05:09 AM
Last Post: spartanheed_imp
  OEM ONLY HEATED GRIPS peterbaron 4 547 10-09-2018, 10:59 AM
Last Post: peterbaron

Forum Jump:


Users browsing this thread: 1 Guest(s)