Login

Nachodaddy · 01-30-2024, 11:42 AM

(01-30-2024, 06:31 AM)peterbaron_imp Wrote:
(01-30-2024, 05:53 AM)Nachodaddy_imp Wrote: Would it be that difficult to make those with a 3Dprinter?

Probably not... but you would run out of ink very quickly during 3D processing and your project could fail before you refill it...

Probably not... but you would run out of ink very quickly during 3D processing and your project could fail before you refill it... Smile

Tev62 · 01-30-2024, 07:58 PM

I found the fork guards on my 2017EX work very well in shielding crud. I used some Triumph ones I had kicking around which were the same diameter. I did have to bring the twin horns out on some washers though as the guards just caught them.

GoldOxide_imp · 01-30-2024, 10:29 PM

(01-30-2024, 07:58 PM)Tev62_imp Wrote: I found the fork guards on my 2017EX work very well in shielding crud. I used some Triumph ones I had kicking around which were the same diameter. I did have to bring the twin horns out on some washers though as the guards just caught them.

I like this shot, Tev.

Gone in 60 · 01-31-2024, 03:12 AM

Hmm.. didn't think about the horns. I put slightly smaller ones on my CB, wonder if that would help.

Tev62 · 01-31-2024, 08:05 PM

(01-30-2024, 10:29 PM)GoldOxide_imp Wrote:
(01-30-2024, 07:58 PM)Tev62_imp Wrote: I found the fork guards on my 2017EX work very well in shielding crud. I used some Triumph ones I had kicking around which were the same diameter. I did have to bring the twin horns out on some washers though as the guards just caught them.

I like this shot, Tev.

I like this shot, Tev.
My lads North American spec Ninja EX250F, this colour was never sold in Europe. It is ironic that the modern plastic adorned Ninja is a carburetted 2004 and the chromed up CB is a fuel injected 2017MY. Smile

peterbaron · 02-06-2024, 05:24 AM

New guards already installed and tested on my white CB

[Image: 3d60d0e0bcff6001a213d0b480518cd3.jpg]

[Image: 9e91c35619fd037989c40c4336069d84.jpg]

My DLX will get them installed this week.

17-CB-002 · 02-09-2024, 02:08 AM

Mine is home made from a PCV pipe back in 2017 and not as nice as yours PB.

It is secured via a tie-wrap.

It is tall enough but will not contact the horns during hard braking.

Does the job properly and happy with the price $2.

peterbaron · 02-09-2024, 03:37 AM

…. needs front tire : Smile

)

17-CB-002 · 02-11-2024, 06:00 AM

(02-09-2024, 03:37 AM)peterbaron_imp Wrote: …. needs front tire :)

Old picture Wink

New boots is Bridgestone T32 series tires.

peterbaron · 02-11-2024, 09:19 PM

Fork guards for my DLX

[Image: 8c5f162fdd421110ff318533c83f620b.jpg]

[Image: 694d5b5ae7c569d407f9b50606c64cd4.jpg]

Login
Username:
Password:	Lost Password?
	Remember me

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	Öhlins front fork	Yama_imp	4	353	06-28-2023, 09:43 AM Last Post: Lord Popgun
	SW Motech engine guards	gretle_2.0	3	386	06-05-2022, 09:54 AM Last Post: gretle_2.0
	R-Gaza engine guards	Nightryder22_imp	9	699	04-15-2022, 12:10 AM Last Post: Nightryder22_imp
	Chain guards	Rexburgtom_imp	26	1,397	01-12-2022, 05:32 AM Last Post: 2017EX_imp
	Frame sliders/engine guards	Cqrlm911_imp	81	3,792	11-10-2021, 06:46 AM Last Post: Houtman_imp
	New YSS shocks,Hyperpro Progressive front springs,gators	ozigoo	10	778	10-03-2021, 04:03 AM Last Post: Tev62
	Yamaha hand guards	jedd_imp	4	767	12-23-2020, 01:29 PM Last Post: GoldOxide_imp
	hand guards and heated grips	misterprofessionality	33	1,925	11-16-2020, 10:06 AM Last Post: mrded_imp
	Engine guards	Wind_imp	33	1,528	07-06-2020, 05:28 PM Last Post: michael1954
	Gators -Honda vs Kawa vs Triump	ozigoo	8	477	05-28-2020, 11:12 PM Last Post: misterprofessionality

Threaded Mode Front fork seal Guards, not gators
Author	Message