+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: Pullback risers (/showthread.php?tid=8816)
Pages:
1
2
Pullback risers - el duque_imp - 04-03-2018
I don't mind the bars the way they are. The position seems to work with the little fairing. But it would be a bit more comfortable if they were up and back a little. My only concern is I'll be more upright and maybe a bit more of a target for the wind.
Any suggestions?
RE: Pullback risers - Mscb1100_imp - 04-03-2018
I put 2 inch Roxx risers on mine with a taller K&H seat so I’m pretty upright and did not notice any increase in wind drag.
RE: Pullback risers - pdedse - 04-03-2018
I used an older version of these on my '14 Standard that made a big difference.
The cables seemed to have just enough play without having to do anything.
The risers bring the bar up and back closer to you.
[url=http://www.twistedthrottle.com/sw-motech-barback-riser-kit-to-fit-22mm-handlebars-for-many-aprilia-bmw-honda-kawasaki-ktm-suzuki-triumph-yamaha-models-30mm-rise-21mm-back-silver]SW-Motech Barback
[url=http://d1l4i7f87txqmq.cloudfront.net/Installation%20Instructions/SW-Motech/LEH/leh_00_039_21000_x.pdf]Mounting instructions gives a good look
I didn't notice any difference with wind, but much more comfortable riding position for me.
RE: Pullback risers - jimgl3_imp - 04-03-2018
$16 off Ebay did the same thing as the Roxx. the bottom part was a tad loose. final solution was wrapped once around the middle with safety wire to fill the gap and bolted down. solid as a rock now and you can't tell looking at it.
RE: Pullback risers - Nortoon_imp - 04-04-2018
After another forum member suggested them, I bought a pair of GenMar risers. They raise the bars up 1" and back 1 3/8 inches. Unfortunately I will have to wait until May to try them.
RE: Pullback risers - el duque_imp - 04-04-2018
thanks.
all good suggestions that i will look into.
RE: Pullback risers - LikeAfox_imp - 04-04-2018
(04-03-2018, 08:41 PM)jimgl3_imp Wrote: $16 off Ebay did the same thing as the Roxx. the bottom part was a tad loose. final solution was wrapped once around the middle with safety wire to fill the gap and bolted down. solid as a rock now and you can't tell looking at it.
Can you link to that or similar item?
RE: Pullback risers - jimgl3_imp - 04-04-2018
[url=https://www.ebay.com/itm/Pair-Motorcycle-HandleBar-Handle-Fat-Bar-Mount-Clamps-Riser-Universal-7-8-22mm/173092647013?hash=item284d203065:g:eF0AAOSwWktaWCNt&vxp=mtr]https://www.ebay.com/itm/Pair-Motorcycle...Nt&vxp=mtr
in case that doesn't work, here's the description to search
Pair-Motorcycle-HandleBar-Handle-Fat-Bar-Mount-Clamps-Riser-Universal-7-8-039-039-22mm
RE: Pullback risers - LikeAfox_imp - 04-04-2018
Thank you. They are definitely pullback kind, not just straight up risers?
Also, does anyone ever tried using a rubber gasket to decrease vibration? Touring bikes do that upgrade often.
RE: Pullback risers - jimgl3_imp - 04-05-2018
yes, they swivel any way you want them. I tried rubber for the slight mis-fit that I described and it worked ok. it did dampen vibration like you suggest, but I just couldn't get used to the lack of a really solid feel to the bars. that's why I finally went with the safety wire.