+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: I need Grip Recommendations (/showthread.php?tid=8303)
Pages:
1
2
I need Grip Recommendations - cbolling_imp - 10-31-2020
I just cut off my grip puppies and installed my new grips. The problem is they are too short. Any recommendations for grips that actually fit?
RE: I need Grip Recommendations - Houtman_imp - 10-31-2020
Years ago some one said : measure twice and cut once.....
I do like the OEM grips on the CB 1100.
RE: I need Grip Recommendations - the Ferret - 10-31-2020
I use 719 Gel grips
RE: I need Grip Recommendations - cbolling_imp - 10-31-2020
Are the 719 grips long enough? It says that they are 125 mm. Which seems just a bit too short. That is why I am so confused. Grips seem to be pretty standard in length and the ones I bought are just too short.
RE: I need Grip Recommendations - pekingduck - 10-31-2020
Grip length is all over the place. CB1100 stock grips are about 135mm, as are most modern street bikes. Dirt bike grips are like 110-115mm.
You could always slide them in further and have the gap on the outside. Some 1" heat shrink or black tape can take up 10-15mm gap.
RE: I need Grip Recommendations - cbolling_imp - 10-31-2020
At this point I am not real picky about what I have to get. I just want them to fit. I figure someone on here has replaced their grips with ones that actually fit. I found some that are the proper length put they are closed end.
Ok, I just found a 135mm set on EBay and ordered them.
RE: I need Grip Recommendations - GoldOxide_imp - 10-31-2020
Grip Puppies on top of the OEM grips.
RE: I need Grip Recommendations - pekingduck - 10-31-2020
(10-31-2020, 12:52 PM)cbolling_imp Wrote: At this point I am not real picky about what I have to get. I just want them to fit. I figure someone on here has replaced their grips with ones that actually fit. I found some that are the proper length put they are closed end.
Ok, I just found a 135mm set on EBay and ordered them.
When I'm using closed-ended grips and I need to make them open-ended, I slide them on as far as they will go, then using a steel hammer, I whack the end and it cuts/pinches the bar and leaves the end open. I've tried cutting them open with a razor or knife, and they haven't been as clean. Sounds crude, but effective.
RE: I need Grip Recommendations - cbolling_imp - 11-01-2020
(10-31-2020, 01:44 PM)GoldOxide_imp Wrote: Grip Puppies on top of the OEM grips.
That is what I started with. Way too fat. I have had grip puppies before but these were way fatter than normal.
RE: I need Grip Recommendations - tod.branko_imp - 11-01-2020
(10-31-2020, 07:28 AM)cbolling_imp Wrote: I just cut off my grip puppies and installed my new grips. The problem is they are too short. Any recommendations for grips that actually fit?I have the same grips only red, but I also have dirt bars, so what I did is - i cut off the throttle twist tube sleeve, still plenty big for my xxl gloves. I needed to cut off the sides too to fit the bar-end mirrors
![[Image: c48f2c977752a2bb9c30d96e4d2ed09a.jpg]](https://cb1100forum.net/forum/uploads/imp/202011/c48f2c977752a2bb9c30d96e4d2ed09a.jpg)
Sent from my ONEPLUS A5010 using Tapatalk