2017 Honda CB1100EX modifications

2017 Honda CB1100EX modifications - Printable Version

+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Mechanical & Technical (https://cb1100forum.net/forum/forumdisplay.php?fid=7)
+--- Thread: 2017 Honda CB1100EX modifications (/showthread.php?tid=4164)

Pages: 1 2 3

2017 Honda CB1100EX modifications - kennyw - 04-21-2018

Since I traded a 2013 CB1100 in on the new EX I have a few modifications that were removed to use on the 2017. I am starting with checking compatibility of the old parts at first.

First up was the Corbin seat. Fits perfectly with a small gap at the tank. Barely noticeable unless you know to look. The wide seat actually matches the lines of the 2017 better than the 2013.
[Image: 796dee53095a42b8f071d5333e0f989e.jpg]

[Image: 796dee53095a42b8f071d5333e0f989e.jpg]

[Image: 1ba0c837987cbf9904ea24b0ece80d49.jpg]

[Image: 7dfb48533f4e94cb771a086a1458d49c.jpg]

[Image: a57fbfeeff5f5ed90d1d0a6eb798c455.jpg]

Second the Emgo Venom fairing. I have only placed it on the headlight bucket without installing bolts so far but the fit looks better than the 2013. With no trimming needed. I may but down a new one since I trimmed this one to fit a 2013.
[Image: ae9ce15422f87d8a88b4a9b9682297e1.jpg]

[Image: ae9ce15422f87d8a88b4a9b9682297e1.jpg]

[Image: 4e799d39baef657ca12a8c92af5f756d.jpg]

Next up the license plate bracket. I have a metalmaven license plate bracket that was used on my 2013 but found it would not be the best fit for the 2017. First it needs spacers to move away from the taillight housing. Then there is a third bolt hole in the lower fender to deal with that is not covered by the bracket. My solution is to make a new plate with the three mounting bolt holes. [Image: edd519e0795fab223b57bc580d0a25f4.jpg]

[Image: edd519e0795fab223b57bc580d0a25f4.jpg]

[Image: 5a496d88197cc91f2f86e96b1896b3c2.jpg]

[Image: 8b0b6c8dfc218e31e72b330269821aa8.jpg]

[Image: 1cf1bea4361930f13c3cb3ce597f7e4a.jpg]

[Image: 6452c2cc0dafabb27b1469c2b9430db1.jpg]

[Image: 4f6925c5423e41dc225c83d52aeff35f.jpg]

[Image: 0d468e9daf38c06cdd4b8bdba3f11378.jpg]

[Image: e59d70ae350f74d0e06a42a08231d4ea.jpg]

RE: 2017 Honda CB1100EX modifications - the Ferret - 04-21-2018

Cracklin work kenny Thumbs Up

RE: 2017 Honda CB1100EX modifications - LongRanger_imp - 04-21-2018

Looks great! Please enlighten me on the reason for modifying the license plate bracket.

RE: 2017 Honda CB1100EX modifications - SportsterDoc - 04-21-2018

The small gap from seat to tank looks just right to keep seat from rubbing tank paint.

Nice job on counter sinking the license mounting plate.
Your pattern looks the same as what I did, other than I mounted it higher, loosing all 3 reflectors, showing more rear fender.
Was lucky enough to find mirror finish stainless steel, so the back side of the mounting plate looks chrome.

(04-21-2018, 09:18 AM)LongRanger_imp Wrote: Looks great! Please enlighten me on the reason for modifying the license plate bracket.

Appearance
PM your email if you want pics of mine.

RE: 2017 Honda CB1100EX modifications - LongRanger_imp - 04-21-2018

Gotcha, thanks. It looks like it'll leave a visible hole (and grommet!) at the lower edge of the fender. Looking forward to seeing the final results!

RE: 2017 Honda CB1100EX modifications - pdedse - 04-21-2018

(04-21-2018, 08:11 AM)kennyw_imp Wrote: Since I traded a 2013 CB1100 in on the new EX I have a few modifications that were removed to use on the 2017. I am starting with checking compatibility of the old parts at first.

First up was the Corbin seat. Fits perfectly with a small gap at the tank. Barely noticeable unless you know to look. The wide seat actually matches the lines of the 2017 better than the 2013.

Second the Emgo Venom fairing. I have only placed it on the headlight bucket without installing bolts so far but the fit looks better than the 2013. With no trimming needed. I may but down a new one since I trimmed this one to fit a 2013.

Next up the license plate bracket. I have a metalmaven license plate bracket that was used on my 2013 but found it would not be the best fit for the 2017. First it needs spacers to move away from the taillight housing. Then there is a third bolt hole in the lower fender to deal with that is not covered by the bracket. My solution is to make a new plate with the three mounting bolt holes.

I ran into the same type thing...thanks for the photos and dimensions!

RE: 2017 Honda CB1100EX modifications - SportsterDoc - 04-21-2018

(04-21-2018, 09:30 AM)LongRanger_imp Wrote: Gotcha, thanks. It looks like it'll leave a visible hole (and grommet!) at the lower edge of the fender. Looking forward to seeing the final results!

Interesting, as my 2014 has a two bolt (6 mm) bracket with third point rubber "bumper" on the bracket.

2017 Honda CB1100EX modifications - kennyw - 04-21-2018

The bracket I have installed is for the 2013/14. The sketch I made will move the plate down and cover the bottom hole. I just need to get one made and test fit for verification.

2017 Honda CB1100EX modifications - kennyw - 04-24-2018

I finished mounting the fairing and added usb power to the phone mount. The fairing looks like it was made for this bike. No issues mounting it other than using longer bolts than stock. I also added a washer in between the fairing and headlight bracket to fill the recess for the factory bolt head. Otherwise the fairing plastic would bend into that recess. [Image: 7fed33dd4f6d3cc6492a0f19e3a5d0c9.jpg]

[Image: 7fed33dd4f6d3cc6492a0f19e3a5d0c9.jpg]

[Image: 1952914b6cbd551e2fe47c9445b8a00d.jpg]

[Image: 46366c593223244685b9ce79efab5bf0.jpg]

RE: 2017 Honda CB1100EX modifications - the Ferret - 04-24-2018

Looking good Kenny. Does that phone/GPS holder impede your access to the ignition key?

Edit: ahh I see now that it is off to the right. I thought it was in the center.