+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: Chip Beck Spec Low Handlebar/Mirrors Mod. (/showthread.php?tid=9900)
Chip Beck Spec Low Handlebar/Mirrors Mod. - bustin dailey_imp - 04-01-2015
(03-24-2015, 10:51 PM)coryredick_imp Wrote: Ordered these bars and had them put on at the Honda dealership for my 600 mile service. I am 6' 2" and have long arms. I love the new sportier riding position and I don't feel like I lost any control or leverage whatsoever and they look fantastic. Also, we decided that drilling holes wasn't necessary as it didn't effect the position of the levers enough to warrant. Thanks Chip for doing the leg work on this!
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
RE: Chip Beck Spec Low Handlebar/Mirrors Mod. - coryredick_imp - 04-03-2015
(04-01-2015, 12:54 PM)bustin dailey_imp Wrote:(03-24-2015, 10:51 PM)coryredick_imp Wrote: Ordered these bars and had them put on at the Honda dealership for my 600 mile service. I am 6' 2" and have long arms. I love the new sportier riding position and I don't feel like I lost any control or leverage whatsoever and they look fantastic. Also, we decided that drilling holes wasn't necessary as it didn't effect the position of the levers enough to warrant. Thanks Chip for doing the leg work on this!
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
Chip Beck Spec Low Handlebar/Mirrors Mod. - bustin dailey_imp - 04-03-2015
(04-03-2015, 12:20 AM)coryredick_imp Wrote:(04-01-2015, 12:54 PM)bustin dailey_imp Wrote:(03-24-2015, 10:51 PM)coryredick_imp Wrote: Ordered these bars and had them put on at the Honda dealership for my 600 mile service. I am 6' 2" and have long arms. I love the new sportier riding position and I don't feel like I lost any control or leverage whatsoever and they look fantastic. Also, we decided that drilling holes wasn't necessary as it didn't effect the position of the levers enough to warrant. Thanks Chip for doing the leg work on this!
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
Ah, must be a difference in the control pin location on the 2014 models, either that or they ground the pin off on the controls, which would get them around drilling new holes in the bars also. The only reason we drilled new holes was so I could be certain the throttle wouldn't eventually rotate on the bar. But again, mine being a 2013 I bet the controls themselves are different too.
Either way, your bike looks great! Thanks for sharing!
RE: Chip Beck Spec Low Handlebar/Mirrors Mod. - coryredick_imp - 04-03-2015
(04-03-2015, 02:55 AM)bustin dailey_imp Wrote:(04-03-2015, 12:20 AM)coryredick_imp Wrote:(04-01-2015, 12:54 PM)bustin dailey_imp Wrote:(03-24-2015, 10:51 PM)coryredick_imp Wrote: Ordered these bars and had them put on at the Honda dealership for my 600 mile service. I am 6' 2" and have long arms. I love the new sportier riding position and I don't feel like I lost any control or leverage whatsoever and they look fantastic. Also, we decided that drilling holes wasn't necessary as it didn't effect the position of the levers enough to warrant. Thanks Chip for doing the leg work on this!
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
Ah, must be a difference in the control pin location on the 2014 models, either that or they ground the pin off on the controls, which would get them around drilling new holes in the bars also. The only reason we drilled new holes was so I could be certain the throttle wouldn't eventually rotate on the bar. But again, mine being a 2013 I bet the controls themselves are different too.
Either way, your bike looks great! Thanks for sharing!
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
Ah, must be a difference in the control pin location on the 2014 models, either that or they ground the pin off on the controls, which would get them around drilling new holes in the bars also. The only reason we drilled new holes was so I could be certain the throttle wouldn't eventually rotate on the bar. But again, mine being a 2013 I bet the controls themselves are different too.
Either way, your bike looks great! Thanks for sharing!
Yeah, that must be it, for some reason I think I remember reading that the pin locations were different. Your bike looks great too, love the gaiters. What bag is that? I really need one and that is about nicest I've seen as far as low key.
Chip Beck Spec Low Handlebar/Mirrors Mod. - bustin dailey_imp - 04-04-2015
The bag is a saddleman tunnel bag. I saw it on another members bike in one of the bag threads on here. I agree it is the most low key one I have seen on our bikes so far.
I think I'm going to get a bag mount for one side so I can strap it off the side when I need the seat for a passenger.
Here's a link : Saddlemen TS1620S Tunnel/Tail Bag - Black https://www.amazon.com/dp/B0041QDVK0/ref=cm_sw_r_awd_pjhivb1S62KTA
https://www.amazon.com/dp/B0041QDVK0/ref=cm_sw_r_awd_pjhivb1S62KTA
RE: Chip Beck Spec Low Handlebar/Mirrors Mod. - coryredick_imp - 04-06-2015
Nice. Thanks bro.
RE: Chip Beck Spec Low Handlebar/Mirrors Mod. - metalmaven_imp - 04-09-2015
Hey Chip, is that your bike with the corbin seat on page one? I was thinking about getting that seat..
RE: Chip Beck Spec Low Handlebar/Mirrors Mod. - ChipBeck_imp - 04-10-2015
(04-09-2015, 09:21 PM)metalmaven_imp Wrote: Hey Chip, is that your bike with the corbin seat on page one? I was thinking about getting that seat..
Metal,
Yes that's my bike. I had Corbin make a special "Chip Beck Spec" seat. It has no tuck & roll stitching, no back rest slots, and no ugly flap on the back. It's clean and simple like the stock seat. Several members have ordered duplicates of my seat. Corbin will try to sell you their stock version as they don't like to change it. They told a couple people that the tuck & roll is necessary to keep the leather in place. That is not true as the vast majority of Corbin seats do not have tuck & roll stitching and my seat is perfect after a year and a half. There is a thread about this seat in the "how to" section of this Forum. Cheers.
Chip
RE: Chip Beck Spec Low Handlebar/Mirrors Mod. - blackened'14_imp - 08-20-2015
Great info! To be sure before ordering, is the consensus that this mod does work on the '14 standards? I read that Chucky had some problems with throttle, but others have successfully completed it & are happy?
[quote='blackened'14' pid='103212' dateline='1440087121']
RE: Chip Beck Spec Low Handlebar/Mirrors Mod. - Liable_imp - 12-01-2015
(04-03-2015, 12:20 AM)coryredick_imp Wrote:(04-01-2015, 12:54 PM)bustin dailey_imp Wrote:(03-24-2015, 10:51 PM)coryredick_imp Wrote: Ordered these bars and had them put on at the Honda dealership for my 600 mile service. I am 6' 2" and have long arms. I love the new sportier riding position and I don't feel like I lost any control or leverage whatsoever and they look fantastic. Also, we decided that drilling holes wasn't necessary as it didn't effect the position of the levers enough to warrant. Thanks Chip for doing the leg work on this!
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
I installed mine this weekend. I don't know what we did different, but without drilling new holes the controls were rotated way too far down, leaving the throttle cable coming out of the control pointing up. I thought it looked funny.
Care to share a photo of yours for reference for everyone?
Installed my bars and mirrors this past weekend, as well as some fork gaitors.
I am 6'4" with very long arms, so for me this completely transformed the bike. I am far more comfortable on long trips, and in town the bike handles much better.
Sure. My controls are in a very comfortable position and the cables re-routed nicely I think, but matter of opinion I guess.
So sorry to necro this post, but coryredick, if you're still around. What year CB500F bars did you use? 2013?
Anyone know if year matters for this mod? I've got a 2014 std and I was excited to hear you didn't have to drill.