+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: EOT meter for OEM oil cooler (/showthread.php?tid=9153)
RE: EOT meter for OEM oil cooler - dsinned_imp - 08-05-2016
You're all set. It looks good there!
RE: EOT meter for OEM oil cooler - Lord Popgun - 08-05-2016
The hard wired one you mentioned might be nice, but in my experience with tach/hour meters similar to this, the batteries last many years. And I think it can be changed as there were screws on the back of the meter.
RE: EOT meter for OEM oil cooler - dsinned_imp - 08-05-2016
The TTV also is self powered by its own internal battery. The connection to the bike's battery is for controlling a fan, but also can be monitored as well.
EOT meter for OEM oil cooler - Elipten_imp - 08-05-2016
Appears to be missing an amp meter, altimeter, compass, and humidity gauge. Then it would be fully instrumented.
RE: EOT meter for OEM oil cooler - Lord Popgun - 08-05-2016
My phone will do a couple of those things
. 
EOT meter for OEM oil cooler - Elipten_imp - 08-05-2016
True enough
RE: EOT meter for OEM oil cooler - Roadwarrior_imp - 08-13-2016
Engine oil needs to see temps. regularly (but not constant) above 212. This is needed to evaporate the moisture in the oil created by internal combustion. If it is not evaporated it will mix with other chemicals created by internal combustion to create acid, which will erode seals, bearings,
rings, cyl. bore, etc. Most oils start breaking down at about 275 degrees,
but a good synthetic oil is good to about 350 degrees. Probably why the warning light is set for 340.
RE: EOT meter for OEM oil cooler - flynrider - 08-13-2016
Although the boiling temperature of water is 212F, your oil doesn't need to get quite that hot. Moisture in the crankcase will begin to vaporize at around 160F - 170F, and will exit through the crankcase breather.
That said, I strongly agree with all of reasons why oil needs to get hot enough to purge moisture. Starting a cold air cooled engine will send plenty of acidic moisture into the crankcase, due to the cold ring gap common to these engines (the gap closes as the engine warms up). Numerous cold starts without reaching normal operating temps will eventually result in a corrosive, white colored goo in the crankcase. If you ever see that, it's a clue that your oil is not getting hot enough.
RE: EOT meter for OEM oil cooler - HillCountryRider_imp - 12-20-2016
(08-13-2016, 05:51 AM)Roadwarrior_imp Wrote: Engine oil needs to see temps. regularly (but not constant) above 212. This is needed to evaporate the moisture in the oil created by internal combustion. If it is not evaporated it will mix with other chemicals created by internal combustion to create acid, which will erode seals, bearings,
rings, cyl. bore, etc. Most oils start breaking down at about 275 degrees,
but a good synthetic oil is good to about 350 degrees. Probably why the warning light is set for 340.
Just curious how you know the High Oil Temperature Indicator is set to come on for 340F? Is it in service manual specs? Thanks
RE: EOT meter for OEM oil cooler - Cormanus - 12-20-2016
G'day HillCountryRider and welcome to the forum. Why not pop over to the New Members Section, tell us all about yourself and show us some pictures of your bike(s)? We're desperate for entertainment around here.