The CB1100 Community Forum
Larger rear sprocket - Printable Version

+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: General Discussion (https://cb1100forum.net/forum/forumdisplay.php?fid=6)
+--- Thread: Larger rear sprocket (/showthread.php?tid=1436)

Pages: 1 2 3 4 5 6 7 8 9 10

Larger rear sprocket - PowerDubs_imp - 04-03-2018

I’m not sure if the 2003 uses the same part. The 900RR generation that would fit is the one from the early 90s 9394 etc..


Sent from my iPhone using Tapatalk

RE: Larger rear sprocket - jimgl3_imp - 04-03-2018

someone find me a 37 tooth for less than $60. the JT is aluminum. I'm not paying $60 for an aluminum sprocket. if it was steel I would pay it because it would last.

RE: Larger rear sprocket - Cormanus - 04-03-2018

(04-03-2018, 03:16 AM)PowerDubs_imp Wrote: I’m not sure if the 2003 uses the same part. The 900RR generation that would fit is the one from the early 90s 9394 etc..


Sent from my iPhone using Tapatalk

OK, there are two offerings for the 1994 CBR900RRR:
[ul] [li]"Sprocket Comp., Final Driven (42T) P/N 41200-MW0-000"[/li] [li]"Sprocket Final Driven (43T) P/N 41201-MAL-600"
[/li][/ul] Again, check the parts fiche [url=http://www.peterhillhonda.com.au/honda-parts-epc]here. Peter Hill seems to have a good historic parts list. For what it's worth, the 43T sprocket part number matches with that on PartsFish, although there is no 42T sprocket there. Makes me think the P/N is probably right. Mr T could get it, maybe, if you can't source it locally.

RE: Larger rear sprocket - PowerDubs_imp - 04-03-2018

Thanks. Appears to be discontinued. I guess I'll just order the JT sprocket one above.

RE: Larger rear sprocket - Cormanus - 04-04-2018

Have you tried Mr T?

RE: Larger rear sprocket - PowerDubs_imp - 04-04-2018

No, but if Honda is listing it as discontinued that is different than him just tracking down a foreign part #.

Also- it appears that even when available, the cost was 5 times the cost of a comparable aftermarket part which is insane. A little more cost for a little more piece of mind- ok. But not that much.

Smile

RE: Larger rear sprocket - Flytech99_imp - 04-04-2018

If the early 900RR sprocket is compatible with the CB, are there any quality 42 tooth aftermarket options for it? Maybe cross-referencing to a different model will yield better results than the CB. I’ve seen that before with a few other parts.

RE: Larger rear sprocket - Retsel_imp - 04-04-2018

(04-04-2018, 09:46 AM)Flytech99_imp Wrote: If the early 900RR sprocket is compatible with the CB, are there any quality 42 tooth aftermarket options for it? Maybe cross-referencing to a different model will yield better results than the CB. I’ve seen that before with a few other parts.
That's exactly what we did with JT Sprocket. This is the result. Same part number for CB1100 and 900RR.[Image: ab2eba83fd3c2b6046b287c793db9774.jpg]

Sent from my SM-T710 using Tapatalk

RE: Larger rear sprocket - Flytech99_imp - 04-04-2018

(04-04-2018, 10:06 AM)Retsel_imp Wrote:
(04-04-2018, 09:46 AM)Flytech99_imp Wrote: If the early 900RR sprocket is compatible with the CB, are there any quality 42 tooth aftermarket options for it? Maybe cross-referencing to a different model will yield better results than the CB. I’ve seen that before with a few other parts.
That's exactly what we did with JT Sprocket. This is the result. Same part number for CB1100 and 900RR.[Image: ab2eba83fd3c2b6046b287c793db9774.jpg]

Sent from my SM-T710 using Tapatalk
That's exactly what we did with JT Sprocket. This is the result. Same part number for CB1100 and 900RR.[Image: 9b2f763d7a455f8371ae24024d9df1b0.jpg]

Sent from my SM-T710 using Tapatalk
Gotcha! I looked at that page wrong the first time. I see now the part number is the “same” although the number of teeth vary based on application.

RE: Larger rear sprocket - PowerDubs_imp - 04-04-2018

Smile

Yup