+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: Thinking of a new gadget... (/showthread.php?tid=8366)
RE: Thinking of a new gadget... - GoldOxide_imp - 12-04-2018
Very thorough response Csory. Bonus for the idle time battery draw. Approximately 1 mA standby draw is not too bad. I think many motorcycle alarm systems draw 20 times that. I know the earlier generation HD V-Rods with alarm systems drew so much standby current that the battery was destroyed after two to three months. It was a real pain in the butt during remote winter storage (maybe a bug in the implementation).
RE: Thinking of a new gadget... - Csory_imp - 12-05-2018
GoldOxide: The main factor with limiting off-state power draw is the voltage converter itself. Quiescent current of the aforementioned TRACO unit is 1mA. Anything lower than that requires a custom built buck reg and that would not fit into the form factor. Will take a look at it though - if I give up being "homemade" and hire an SMD fab, this still might be doable. Just to make sure that we're on the same page: I intend to connect this to a switched circuit -> zero power drawn while ignition is off.
RE: Thinking of a new gadget... - GoldOxide_imp - 12-05-2018
(12-05-2018, 12:33 AM)Csory_imp Wrote: GoldOxide: The main factor with limiting off-state power draw is the voltage converter itself. Quiescent current of the aforementioned TRACO unit is 1mA. Anything lower than that requires a custom built buck reg and that would not fit into the form factor. Will take a look at it though - if I give up being "homemade" and hire an SMD fab, this still might be doable. Just to make sure that we're on the same page: I intend to connect this to a switched circuit -> zero power drawn while ignition is off.
Sounds good. I was going to ask if you were going to add a relay that was power by the ignition/accessory circuit, but looks like you are well ahead of that. Doesn't look like you need a relay either.
RE: Thinking of a new gadget... - Csory_imp - 12-05-2018
GoldOxide: Yup, managed to find the OEM grip heater connector under the right-side aluminum cover, already spliced into that for my underseat USB charger. Will hook up this gadget to that too. It is an ignition-switched circuit on a 15A fuse, if memory serves well... Alternatively, could use the same circuit in the headlight assy, just not sure if that red connector is avilable on my MY18.
RE: Thinking of a new gadget... - GoldOxide_imp - 12-06-2018
That is awesome convenient Csory.
RE: Thinking of a new gadget... - jtopiso_imp - 12-06-2018
(11-23-2018, 11:41 PM)Csory_imp Wrote: Ok, while still waiting for the parts started tinkering with the housing. Attached pictures show renderings of front and rear view. Front window will be made of acrylic or polycarbonate. Housing will be filled with electronic grade water-clear silicone to seal from the elements. Ambient light sensor will face downward, buried in silicone but close to the surface. Next step is to have it 3D printed (or print myself if I'm brave enough) to see how it fits.
Regarding the housing, why don't you buy one of those clocks or thermometers which clamp on the handlebar, and use the casing to put your gadget in it?
for example:
https://alexnld.com/product/22-28mm-motorcycle-clock-thermometer-luminous-waterproof-handle-bar-mount/
You can use that, and then 3D print the internal structure so your electronics fit nice into that.
I think it will give you a cleaner installation. I'd buy one! (if in Celsius
)
RE: Thinking of a new gadget... - GoldOxide_imp - 12-06-2018
I reckon for some there is the excitement and satisfaction of controlling the innovation and entire production.
RE: Thinking of a new gadget... - Csory_imp - 12-07-2018
jtopiso: Thanks for the tip! I checked these handlebar mounted instruments and found them to be a bit "out of picture" on the CB. I might be wrong, but hope to end up with an almost factory-looking "disguise" for my gadget...
RE: Thinking of a new gadget... - rboe - 12-09-2018
Dang cool! Gonna offer them up to the group?
RE: Thinking of a new gadget... - Csory_imp - 12-10-2018
Rboe: sure, will put’em under the “homemade for sale” (or whatever is appropriate) thread, but if and only I’m 110% happy with the end result. Right now working on the housing - tested a bunch of iterations with surface finish. The winner process is 160-grit sanded, epoxyed, then spray painted with acrylic in matte black. Base material is 3d printed black ABS, 100 micron layer height. Will have to try cutting the front glass with a diamond disc. Obtained a few sheet of laminated antireflex glass (basically cellphone screen protector) but they are quite thin (0.3mm or less than 1/64”). Will post images once managed to cut’em and not break’em