+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: Where to tap speed sensor signal? (/showthread.php?tid=8683)
RE: Where to tap speed sensor signal? - Lord Popgun - 07-05-2018
In my US model 2013 owners manual and service manual (both 2013 and the 2014 with both years) Non-ABS is just CB1100 and ABS models are CB1100A. None of the B,E or any of that.
Then the parts fiches are different. For example, the DLX is listed as CB1100SA AC and the ‘14 standard is CB1100 AC. Whatever all that is.
RE: Where to tap speed sensor signal? - peterbaron - 07-05-2018
For sure Cormanus...
The most important is that it says CB1100
RE: Where to tap speed sensor signal? - PowerDubs_imp - 07-06-2018
Anybody?.....
RE: Where to tap speed sensor signal? - SportsterDoc - 07-06-2018
(07-06-2018, 05:51 AM)PowerDubs_imp Wrote: Anybody?.....
Posts 2 & 3: pink/green (position 1 of 10 pin connector)
RE: Where to tap speed sensor signal? - PowerDubs_imp - 07-06-2018
Unconfirmed or speculation, pick whichever word you want.
I've already had this conversation over PM and it was followed with the caveat of "don't blame us if you smoke your ECU".
I'm cool with that warning- and therefore sit back and wait for confirmation from people more knowledgeable about electronics and testing to let me know.
I on the other hand will be the guinea pig on the cost, labor and risk of having to pretty much replace my entire engine on possible failure of my 'performance' camshafts.
RE: Where to tap speed sensor signal? - Lord Popgun - 07-06-2018
On the ‘14 Non ABS the speed sensor does not go to the ECU. It goes directly to the meter. The meter sends speed data to the ECU on the serial data line.
Max is worried that the device you are installing might have low input impedance and thus load or damage the speed sensor. My thought is that you device designers though of that. I, personally, would do a test tap on the VSP+ line and see what happens. The instructions for your device say to do that so I think, but cannot guarantee, that it would work.
Without a schematic of the device none of us can give you a definite answer.
RE: Where to tap speed sensor signal? - SportsterDoc - 07-06-2018
(07-06-2018, 07:34 AM)PowerDubs_imp Wrote: Unconfirmed or speculation, pick whichever word you want.
I've already had this conversation over PM and it was followed with the caveat of "don't blame us if you smoke your ECU".
I'm cool with that warning- and therefore sit back and wait for confirmation from people more knowledgeable about electronics and testing to let me know.
I on the other hand will be the guinea pig on the cost, labor and risk of having to pretty much replace my entire engine on possible failure of my 'performance' camshafts.
Take a look at your schematic. The speed sensor + is pink/green.
The differences between non ABS and ABS schematics have been sorted, but
the Signal Dynamics website (link previously supplied) advises to connect their white wire to the speed sensor.
For any concerns, contact Signal Dynamics.
RE: Where to tap speed sensor signal? - peterbaron - 07-06-2018
I keep mine without any "miracle gizmos" = simplicity is the key for trouble free riding
RE: Where to tap speed sensor signal? - SportsterDoc - 07-08-2018
Egleaves: Did you get this sorted?
RE: Where to tap speed sensor signal? - PowerDubs_imp - 07-08-2018
I'm going to tap the pink/white wire off the rear wheel sensor later this afternoon and hope for no puffs of smoke from the ecu, power commander, dash, etc...
