The CB1100 Community Forum
Front fork seal Guards, not gators - Printable Version

+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: Front fork seal Guards, not gators (/showthread.php?tid=7925)

Pages: 1 2 3 4

RE: Front fork seal Guards, not gators - Nachodaddy - 01-30-2024

(01-30-2024, 06:31 AM)peterbaron_imp Wrote:
(01-30-2024, 05:53 AM)Nachodaddy_imp Wrote: Would it be that difficult to make those with a 3Dprinter?

Probably not... but you would run out of ink very quickly during 3D processing and your project could fail before you refill it...Smile

Probably not... but you would run out of ink very quickly during 3D processing and your project could fail before you refill it...Smile ROFL

RE: Front fork seal Guards, not gators - Tev62 - 01-30-2024

I found the fork guards on my 2017EX work very well in shielding crud. I used some Triumph ones I had kicking around which were the same diameter. I did have to bring the twin horns out on some washers though as the guards just caught them.



RE: Front fork seal Guards, not gators - GoldOxide_imp - 01-30-2024

(01-30-2024, 07:58 PM)Tev62_imp Wrote: I found the fork guards on my 2017EX work very well in shielding crud. I used some Triumph ones I had kicking around which were the same diameter. I did have to bring the twin horns out on some washers though as the guards just caught them.

I like this shot, Tev.

RE: Front fork seal Guards, not gators - Gone in 60 - 01-31-2024

Hmm.. didn't think about the horns. I put slightly smaller ones on my CB, wonder if that would help.

RE: Front fork seal Guards, not gators - Tev62 - 01-31-2024

(01-30-2024, 10:29 PM)GoldOxide_imp Wrote:
(01-30-2024, 07:58 PM)Tev62_imp Wrote: I found the fork guards on my 2017EX work very well in shielding crud. I used some Triumph ones I had kicking around which were the same diameter. I did have to bring the twin horns out on some washers though as the guards just caught them.

I like this shot, Tev.

I like this shot, Tev.
My lads North American spec Ninja EX250F, this colour was never sold in Europe. It is ironic that the modern plastic adorned Ninja is a carburetted 2004 and the chromed up CB is a fuel injected 2017MY. Smile

RE: Front fork seal Guards, not gators - peterbaron - 02-06-2024

New guards already installed and tested on my white CB

[Image: 3d60d0e0bcff6001a213d0b480518cd3.jpg]

[Image: 9e91c35619fd037989c40c4336069d84.jpg]

My DLX will get them installed this week.

RE: Front fork seal Guards, not gators - 17-CB-002 - 02-09-2024

Mine is home made from a PCV pipe back in 2017 and not as nice as yours PB.

It is secured via a tie-wrap.

It is tall enough but will not contact the horns during hard braking.

Does the job properly and happy with the price $2.




RE: Front fork seal Guards, not gators - peterbaron - 02-09-2024

…. needs front tire :Smile)

RE: Front fork seal Guards, not gators - 17-CB-002 - 02-11-2024

(02-09-2024, 03:37 AM)peterbaron_imp Wrote: …. needs front tire :Smile)

Old pictureWink

New boots is Bridgestone T32 series tires.

RE: Front fork seal Guards, not gators - peterbaron - 02-11-2024

Thumbs Up

Fork guards for my DLX

[Image: 8c5f162fdd421110ff318533c83f620b.jpg]

[Image: 694d5b5ae7c569d407f9b50606c64cd4.jpg]