![]() |
|
Rubber Lever End Thingies - Printable Version +- The CB1100 Community Forum (https://cb1100forum.net/forum) +-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5) +--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8) +--- Thread: Rubber Lever End Thingies (/showthread.php?tid=7863) Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
|
RE: Rubber Lever End Thingies - E11even_Hunnit - 09-21-2021 (09-21-2021, 09:56 AM)peterbaron_imp Wrote:(09-21-2021, 08:11 AM)GoldOxide_imp Wrote:(09-21-2021, 08:07 AM)peterbaron_imp Wrote: Just came back from my favourite, not so local, Honda dealer where I ordered four RLETs.... which should be ready for pick up by the next week.... Wise he is more power better is More RLETs = more power Just found an additional spot for an extra RLET, my car's antenna --> ...assuming RLET syndicate acceptance ![]() ![]() ^^before RLET installation^^ Part # and length of this antenna? RE: Rubber Lever End Thingies - peterbaron - 09-22-2021 (09-21-2021, 10:28 AM)E11even_Hunnit_imp Wrote:(09-21-2021, 09:56 AM)peterbaron_imp Wrote:(09-21-2021, 08:11 AM)GoldOxide_imp Wrote:(09-21-2021, 08:07 AM)peterbaron_imp Wrote: Just came back from my favourite, not so local, Honda dealer where I ordered four RLETs.... which should be ready for pick up by the next week.... ![]() OEM Hyundai antenna mast P/N 96201-1H5000 or 96215-2J100 , roughly C$45 RE: Rubber Lever End Thingies - Nachodaddy - 10-03-2021 Well, it looks like my son will be delivering my 2013 non-abs CB1100 this morning, so I have a few questions. Is it safe to ride without the RLETS, or should I wait? Should I have the fork springs replaced, or get a 2017 fork if I put RLETS on? Will there be a fuel mileage change with the RLETS installed and will it be plus or minus and how much? Has anyone found a source for pink RLETS? Will I need cold weather RLETS for winter months? How many miles can I expect the RLETS to last? Should I have a spare in case one gives out on long trips? Inquiring minds need to know. Thank you in advance. Thank heavens this forum is here. RE: Rubber Lever End Thingies - the Ferret - 10-03-2021 All valid questions, Nachodaddy yes briefly, no no no heck NO no, you live in Arizona more than you are likely to ride no RE: Rubber Lever End Thingies - peterbaron - 10-03-2021 OMG, Nachodaddy, you need private = one on one tutoring lessons from Lord Popgun...not cheap tho!!
RE: Rubber Lever End Thingies - GoldOxide_imp - 10-03-2021 I like your passion Nacho-D. RE: Rubber Lever End Thingies - the Ferret - 05-12-2023 This is such a fun thread to read. Start with Post 1. To the top for newbies and the un-initiated RE: Rubber Lever End Thingies - The A-man - 05-12-2023 There is, however, one note of caution. RLETS mus bt installed on both left and right levers. Otherwise the bike will tend to pull in one direction or the other. OK if you're practicing U-turns in a vacant parking lot, but potentially dangerous on the open highway! RE: Rubber Lever End Thingies - peterbaron - 05-13-2023 (05-12-2023, 11:24 PM)The A-man_imp Wrote: There is, however, one note of caution. RLETS mus bt installed on both left and right levers. Otherwise the bike will tend to pull in one direction or the other. OK if you're practicing U-turns in a vacant parking lot, but potentially dangerous on the open highway! Absolutely, out of balance in the Force is dangerous!! RE: Rubber Lever End Thingies - GoldOxide_imp - 05-13-2023 (05-12-2023, 11:18 PM)The ferret_imp Wrote: This is such a fun thread to read. Start with Post 1. ... and ensure to read the thread to completion. It is a part of the rite. |