+- The CB1100 Community Forum (https://cb1100forum.net/forum)
+-- Forum: Honda CB1100 Discussions (https://cb1100forum.net/forum/forumdisplay.php?fid=5)
+--- Forum: Accessories/Modifications (https://cb1100forum.net/forum/forumdisplay.php?fid=8)
+--- Thread: Rubber Lever End Thingies (/showthread.php?tid=7863)
Pages:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
RE: Rubber Lever End Thingies - Dave Swanson - 03-26-2020
Got mine, go get yours!
[url=https://postimg.cc/KksjSMkH]
![[Image: 11ee7cf3fb505d38a4202ecccab8a695.jpg]](https://cb1100forum.net/forum/uploads/imp/202003/11ee7cf3fb505d38a4202ecccab8a695.jpg)
RE: Rubber Lever End Thingies - Cormanus - 03-26-2020
Photos when they're installed Dave Swanson. Please.
RE: Rubber Lever End Thingies - The A-man - 03-30-2020
A story of (minor) tragedy...with a message of hope!!
It's taken me a few days to get around to writing this... Last Saturday was a beautiful day in the WNC foothills, so I took the CB up to the Brown Mountain Overlook. Nice ride, warm, lots of bikes out. After a few enjoyable miles, I pulled back down into my garage, stopped, put my feet down, then began to lean left and get off. Then WHAM! My helmet and my shoulder hit the wife's Explorer door, the bike lay down on the floor, and the wife came running out! After a moment to recover, we got it standing up and I realized that I had forgotten to put the sidestand down. Here's a Public Service Announcement -- kids, don't do this at home!! So upon inspection, the bike is fine, except for a broken clutch lever.
After finding out that the Asheville Honda (MR Cycles) is closed due to the virus, I found and ordered an OEM lever from Bike Bandit. Then, several days later, I realized that my left side RLET was now trapped on the broken lever! Tragedy! Should I just buy new?? Then I decided that some good old garage shop engineering was called for. There's just no way to pull it off due to friction. Then I realized that there's a small hole in the end. I fired up the air compressor, used my air gun and some WD 40 to blow some air into the end, and it just sort of "burped" out around the lever, and in about 30 seconds, I had the RLET removed safely and ready for re-installation on my new lever when it gets here!
I hope my experience helps someone recover their beloved RLET in the future!
RE: Rubber Lever End Thingies - suhawk305 - 03-30-2020
The main thing is you didn’t get physically hurt, like a broken clavicle. The last place we would want to end up is in an emergency room.
Otherwise, it is awful feeling falling down with your motorcycle. (You know why I know this! ) At least your RLET was recovered and not damaged!
RE: Rubber Lever End Thingies - Ben70_imp - 03-30-2020
Good job A-man
Ben
RE: Rubber Lever End Thingies - the Ferret - 03-31-2020
bummer A man. Glad you were able to save the rlet though
RE: Rubber Lever End Thingies - peterbaron - 03-31-2020
A-man, sorry about your incident and glad to hear you are fracture/hurt free.
RE: Rubber Lever End Thingies - pdedse - 03-31-2020
(03-30-2020, 11:03 PM)The A-man_imp Wrote: A story of (minor) tragedy...with a message of hope!!
It's taken me a few days to get around to writing this... Last Saturday was a beautiful day in the WNC foothills, so I took the CB up to the Brown Mountain Overlook. Nice ride, warm, lots of bikes out. After a few enjoyable miles, I pulled back down into my garage, stopped, put my feet down, then began to lean left and get off. Then WHAM! My helmet and my shoulder hit the wife's Explorer door, the bike lay down on the floor, and the wife came running out! After a moment to recover, we got it standing up and I realized that I had forgotten to put the sidestand down. Here's a Public Service Announcement -- kids, don't do this at home!! So upon inspection, the bike is fine, except for a broken clutch lever.
After finding out that the Asheville Honda (MR Cycles) is closed due to the virus, I found and ordered an OEM lever from Bike Bandit. Then, several days later, I realized that my left side RLET was now trapped on the broken lever! Tragedy! Should I just buy new?? Then I decided that some good old garage shop engineering was called for. There's just no way to pull it off due to friction. Then I realized that there's a small hole in the end. I fired up the air compressor, used my air gun and some WD 40 to blow some air into the end, and it just sort of "burped" out around the lever, and in about 30 seconds, I had the RLET removed safely and ready for re-installation on my new lever when it gets here!
I hope my experience helps someone recover their beloved RLET in the future!
I did the same thing! Before trading in my '14 Standard, I told myself I went to a lot of trouble getting those things and installing them, that they were going on my next bike...and they did...they went on my Triumph Street Twin (only had it for 2 months, wrong bike for me)...now they're on my '17ex.
And the neat thing is that once they are on one bike, they get stretched out and I think the 2nd time around they go on more easily.
RE: Rubber Lever End Thingies - KiowaEagle_imp - 03-31-2020
Ouch A-man! But thank goodness it was only the clutch lever and you weren't damaged either. Good idea with the rlet. I would have just cut it off in frustration....lol
RE: Rubber Lever End Thingies - Houtman_imp - 03-31-2020
Amos , sorry to hear about your "incident " did you have to buy your wife a new SUV ?