The CB1100 Community Forum

I found these emblems on ebay...not cheap but considering the alternative....
http://www.ebay.com/itm/400943664226?_tr..._282wt_972

Copy the whole link. They are plastic and no decal. $67.24.
I think I'm going to try them out.

It says they are "en metal" when you read the description.

You are correct sir! I have a very limited ability to retain details...esp. while grilling a steak and enjoying an adult beverage. Hopefully my wife will not let me back on ebay after another beverage. Gets costly when that happens!

I think they are the ones a member ordered and put on his bike a year or so ago. Nice emblems and looked good.

You should have seen our posts at Christmas. One evening Ferret had to tell us to stop posting until the toddies wore off!

A buddy just got his new 3D printer set up. I will just have to give him a call!
I'll keep you posted.

Searching around Google images I came across Daytona K0 side covers. They are listed on http://japan.webike.net/products/21382975.html
http://img.webike.net/catalogue/10054/74917_1_ls.jpg
for $133.31 a pair. The photo shows the right side and had a faux oil fill cap and vent like the '69 CB750K0. I am considering them in near future.

(06-23-2015, 08:26 AM)britbikes42_imp Wrote: [ -> ]You are correct sir! I have a very limited ability to retain details...esp. while grilling a steak and enjoying an adult beverage. Hopefully my wife will not let me back on ebay after another beverage. Gets costly when that happens!

Just received these emblems...from France evidently. VERY nice, great quality and worth the $. Only issue is the adhesive on the back of the metal emblems is less than scotch tape thick. I am going to get some thicker adhesive tape...I'll try to find the stuff like on the originals as the panels are not dead flat. The "F" will have to be tweaked ever so slightly to conform to the panel but that shouldn't be an issue. I'll post pics when I get them done. Takes forever to get anything by mail here.
Jeff

I have the 1100 Four, self adhering thick plastic emblems by Endurance. Got them from Web!ke. A little under $30.00. Reasonable shipping cost
They fit over the recessed stock emblems on my DLX.

(08-21-2015, 02:32 AM)britbikes42_imp Wrote: [ -> ]

(06-23-2015, 08:26 AM)britbikes42_imp Wrote: [ -> ]You are correct sir! I have a very limited ability to retain details...esp. while grilling a steak and enjoying an adult beverage. Hopefully my wife will not let me back on ebay after another beverage. Gets costly when that happens!

Just received these emblems...from France evidently. VERY nice, great quality and worth the $. Only issue is the adhesive on the back of the metal emblems is less than scotch tape thick. I am going to get some thicker adhesive tape...I'll try to find the stuff like on the originals as the panels are not dead flat. The "F" will have to be tweaked ever so slightly to conform to the panel but that shouldn't be an issue. I'll post pics when I get them done. Takes forever to get anything by mail here.
Jeff

Just received these emblems...from France evidently. VERY nice, great quality and worth the $. Only issue is the adhesive on the back of the metal emblems is less than scotch tape thick. I am going to get some thicker adhesive tape...I'll try to find the stuff like on the originals as the panels are not dead flat. The "F" will have to be tweaked ever so slightly to conform to the panel but that shouldn't be an issue. I'll post pics when I get them done. Takes forever to get anything by mail here.
Jeff
Hi Jeff,

I just ordered a set just like yours from ebay: http://www.ebay.com/itm/401021262436

Did you install them already? Any information/pictures will be greatly appreciated.

Thanks,
Magnus