The CB1100 Community Forum

(02-29-2016, 02:13 PM)gbpack89_imp Wrote: [ -> ]

(02-14-2016, 03:08 AM)WhiskeyUSMC1979_imp Wrote: [ -> ]Aluminum bar end mirrors purchased through Amazon. $40 shipped. Fitted on Renthal Ultra Low bars. Will not work with factory bar weights.







Sent from an undisclosed location

Whiskey, I have the same bars. How do those bar end mirrors mount?

Sent from my VS985 4G using Tapatalk

Typical bar end style. Expanding collars around a central bolt. You tighten the bolt, the collars expand inside the bars.


Sent from an undisclosed location

(04-02-2015, 02:26 PM)xNE0x_imp Wrote: [ -> ]Mine:

Where did you get these xNE0x?

EDIT: nvm, found your thread about them being NC700X mirrors, thx!

I installed a set of the Fugu mirrors from Samurider (http://www.samurider.com/?p=14930), and while they look great, the left one constantly vibrates out of position on bumpy roads or any speed over ~40 mph. The loose connection is the ball joint where the actual mirror connects to the arm. Anyone have any suggestions? Loc-tite?

(04-21-2016, 02:17 AM)12milesout_imp Wrote: [ -> ]I installed a set of the Fugu mirrors from Samurider (http://www.samurider.com/?p=14930), and while they look great, the left one constantly vibrates out of position on bumpy roads or any speed over ~40 mph. The loose connection is the ball joint where the actual mirror connects to the arm. Anyone have any suggestions? Loc-tite?

I have the same problem with my new mirrors being a tad too loose at that ball joint. I was considering trying some BLUE Loc-tite and letting it flow in and around the ball.

Bar Ends require removal of the Factory installed anti-vibration bar weights. Don't think I want to do that so I've ordered the BikeMaster Old School. Revzilla shipped the same day, now waiting their arrival.

(04-28-2016, 07:13 PM)LoneWoof_imp Wrote: [ -> ]Bar Ends require removal of the Factory installed anti-vibration bar weights. Don't think I want to do that so I've ordered the BikeMaster Old School. Revzilla shipped the same day, now waiting their arrival.

If you go with aftermarket bars it's not a big deal. Aluminium bars don't vibrate like the thin steal OEM. Just a fyi

Sent from my VS985 4G using Tapatalk

(04-28-2016, 07:13 PM)LoneWoof_imp Wrote: [ -> ]Bar Ends require removal of the Factory installed anti-vibration bar weights. Don't think I want to do that so I've ordered the BikeMaster Old School. Revzilla shipped the same day, now waiting their arrival.

I was able to put bar and mirrors on mine without removing the inserts, and I was able to keep the bar end weights:

(04-29-2016, 04:12 AM)c-breezy_imp Wrote: [ -> ]

(04-28-2016, 07:13 PM)LoneWoof_imp Wrote: [ -> ]Bar Ends require removal of the Factory installed anti-vibration bar weights. Don't think I want to do that so I've ordered the BikeMaster Old School. Revzilla shipped the same day, now waiting their arrival.

I was able to put bar and mirrors on mine without removing the inserts, and I was able to keep the bar end weights:

How were you able to do that? Thanks, lw

No bar end weights needed with renthal bars and the looks and riding position is so much nicer. Love my renthals. Funny thing is after two sets of aftermarket mirrors i resorted back to the stock knes because they just complement the retro look. I change my mind alot so can always switch back at any time.

(04-29-2016, 04:48 AM)LoneWoof_imp Wrote: [ -> ]

(04-29-2016, 04:12 AM)c-breezy_imp Wrote: [ -> ]

(04-28-2016, 07:13 PM)LoneWoof_imp Wrote: [ -> ]Bar Ends require removal of the Factory installed anti-vibration bar weights. Don't think I want to do that so I've ordered the BikeMaster Old School. Revzilla shipped the same day, now waiting their arrival.

I was able to put bar and mirrors on mine without removing the inserts, and I was able to keep the bar end weights:

How were you able to do that? Thanks, lw

I'll get some pics for you tomorrow morning before my ride