The CB1100 Community Forum

(04-14-2019, 02:16 AM)Charlie Bravo_imp Wrote: [ -> ]

(02-15-2019, 08:53 AM)jimgl3_imp Wrote: [ -> ]pull the end cap off. drill about 8 1/4" holes. replace end cap. nice deep rumble.

I tried that; pretty much no effect at all. Six 3/8" holes. Gonna enlarge to 1/2"

I tried that; pretty much no effect at all. Six 3/8" holes. Gonna enlarge to 1/2"
Not sure what the problem is, it made a significant difference in the sound mine makes.

Other than the subtly improved sound of the Staintune, for me it is also the best looking of the slip ons. It foreshadows the pipes on the 2017 models. However were I to spend my hard-earned on a new exhaust, I think I’d want to go with a 4 into 4.

(04-14-2019, 12:01 PM)TCinNC_imp Wrote: [ -> ]

(04-14-2019, 02:16 AM)Charlie Bravo_imp Wrote: [ -> ]

(02-15-2019, 08:53 AM)jimgl3_imp Wrote: [ -> ]pull the end cap off. drill about 8 1/4" holes. replace end cap. nice deep rumble.

I tried that; pretty much no effect at all. Six 3/8" holes. Gonna enlarge to 1/2"

I tried that; pretty much no effect at all. Six 3/8" holes. Gonna enlarge to 1/2"
Not sure what the problem is, it made a significant difference in the sound mine makes.

I tried that; pretty much no effect at all. Six 3/8" holes. Gonna enlarge to 1/2"
Not sure what the problem is, it made a significant difference in the sound mine makes.
Different years have different internals, but if they are both the same year there should be similar results

(02-21-2019, 05:02 PM)DBM_imp Wrote: [ -> ]

(02-15-2019, 08:53 AM)jimgl3_imp Wrote: [ -> ]pull the end cap off. drill about 8 1/4" holes. replace end cap. nice deep rumble.

Yup. I drilled several 5/8" holes in the end plate, cut off the snooter pipe, painted the inside end plate with flat black heat paint, and used black high heat RTV sealant when l put the end cap back on. Results are better throttle responce with a nice deep rumble but not too loud. Price was right.

Yup. I drilled several 5/8" holes in the end plate, cut off the snooter pipe, painted the inside end plate with flat black heat paint, and used black high heat RTV sealant when l put the end cap back on. Results are better throttle responce with a nice deep rumble but not too loud. Price was right.
What is a snooter pipe?

The small diameter pipe coming through the middle of the exhaust can

(02-16-2019, 05:19 AM)Frulk_imp Wrote: [ -> ]Well, here's a couple pics of the Yosh on a CB. Deeper rumble for sure unless you screw in the removable baffle/silencer. That quiets it down to about stock.

Just got my Yosh RS3. The manual says it needs repacking yearly.
Do everyone do that for your slip-on exhaust?

(02-20-2019, 01:23 PM)GoldOxide_imp Wrote: [ -> ]Mmmm, like that rear tire.

Makes it look like the CB eats things.

Me too! @Ferrealls What's that? I'll need to replace my tires soon.

(02-15-2019, 06:59 AM)spartanheed_imp Wrote: [ -> ]So my bike has the original exhaust on. Does the baffle come out because it sounds like a hairdryer at present!?

Also, do aftermarket slip on cans make much difference to the sound? I know a full system with the cat removed would be the best option but I'm on a budget!

Hands down, the best aftermarket exhaust with the sweetest sound can be had here.
https://www.mcssl.com/store/coffmansexha...8fcb2ee7f3

Dont see a listing for the CB1100 on that site

Kinda nice lookin' though for a certain look.

(05-10-2019, 09:34 AM)The ferret_imp Wrote: [ -> ]Dont see a listing for the CB1100 on that site

Universal