(06-21-2016, 12:03 AM)Inhouse Bob_imp Wrote: [ -> ]It's been asked before by others and ignored, but I'll ask again... do you get any popping on deceleration with this mod? I know that the air injecting PAIR valve thingie can be easily disabled and that's great, but I would rather not do that if it isn't necessary.
So. Popping. Yes or no.
Thanks!
I drilled 6 3/8 in holes and reinstalled the end cap. I have NO decel popping at all.
(06-21-2016, 07:12 AM)TCinNC_imp Wrote: [ -> ] (06-21-2016, 12:03 AM)Inhouse Bob_imp Wrote: [ -> ]It's been asked before by others and ignored, but I'll ask again... do you get any popping on deceleration with this mod? I know that the air injecting PAIR valve thingie can be easily disabled and that's great, but I would rather not do that if it isn't necessary.
So. Popping. Yes or no.
Thanks!
I drilled 6 3/8 in holes and reinstalled the end cap. I have NO decel popping at all.
I drilled 6 3/8 in holes and reinstalled the end cap. I have NO decel popping at all.
Thanks TC. I think it was you that asked this question originally.
(06-21-2016, 09:07 AM)Inhouse Bob_imp Wrote: [ -> ] (06-21-2016, 07:12 AM)TCinNC_imp Wrote: [ -> ] (06-21-2016, 12:03 AM)Inhouse Bob_imp Wrote: [ -> ]It's been asked before by others and ignored, but I'll ask again... do you get any popping on deceleration with this mod? I know that the air injecting PAIR valve thingie can be easily disabled and that's great, but I would rather not do that if it isn't necessary.
So. Popping. Yes or no.
Thanks!
I drilled 6 3/8 in holes and reinstalled the end cap. I have NO decel popping at all.
I drilled 6 3/8 in holes and reinstalled the end cap. I have NO decel popping at all.
Thanks TC. I think it was you that asked this question originally.
I drilled 6 3/8 in holes and reinstalled the end cap. I have NO decel popping at all.
Thanks TC. I think it was you that asked this question originally.
You're welcome!!
I went for the 8 x 3/8 holes (asymmetrically aligned for the OCD's).
Very slight tone improvement, no popping, backfire etc detected under heavy or light decel.
OK, here's a new link to a limited "after" clip taken with a plain ole no frills camera with a video option.
(06-23-2016, 07:12 AM)GaryMNM_imp Wrote: [ -> ]I went for the 8 x 3/8 holes (asymmetrically aligned for the OCD's).
Very slight tone improvement, no popping, backfire etc detected under heavy or light decel.
OK, here's a new link to a limited "after" clip taken with a plain ole no frills camera with a video option.
I just did exactly the same thing. As you say, a bit of a difference and no change in performance, popping, etc. I had fun playing with the drill, though!
(06-23-2016, 07:18 AM)Inhouse Bob_imp Wrote: [ -> ] (06-23-2016, 07:12 AM)GaryMNM_imp Wrote: [ -> ]I went for the 8 x 3/8 holes (asymmetrically aligned for the OCD's).
Very slight tone improvement, no popping, backfire etc detected under heavy or light decel.
OK, here's a new link to a limited "after" clip taken with a plain ole no frills camera with a video option.
I just did exactly the same thing. As you say, a bit of a difference and no change in performance, popping, etc. I had fun playing with the drill, though!
all worth it in the end then
Don't have access to view the video.
did the same thing, with one addition, I cut the pipe off so the exhaust has a clear path. This helped the tone after putting end cap back on.
Used a dremel and cut about 3/8 out from the plate that holes were drilled in
Biggin, please try to quantify the difference with and without tail pipe cut off, and how does it look with the end cap back on? TIA.
(06-23-2016, 11:06 AM)dsinned_imp Wrote: [ -> ]Biggin, please try to quantify the difference with and without tail pipe cut off, and how does it look with the end cap back on? TIA.
The hole is obviously bigger without the pipe looks alright, seems to be little more rumble, not as airy sounding